test received ok in England Barry ... From: Tom & Sue To: VirtualIndian@yahoogroups.com Sent: Wednesday, October 01, 2008 7:45 PM Subject: [Virtual Indian]...
Slightly off topic, but a lot of you have imported bikes from other countries and I need some advice. I am trying to find out the rules/laws of importing a 20+...
good question Steve' my guess would be that it's grand fathered in, as 20 year olds are clasic & 30 year olds are antiques. how many cylinders does it have?...
Guys I don't think those Diesel RE's will be OLD. (ok, after checking they have produced these quite a while)They are made in ......you guess... INDIA. They...
So far I'm not impressed with what I see from the imported gears and 1 set was in an extremely bad way. However as people do more miles on some of the parts...
Mike Tomas
bigchief@...
Oct 2, 2008 5:40 am
109919
Kawasaki make a diesel 650 or 600 for the Yank army top speed 80 mph and gets 100 mpg I know they will never come to Australia but mabe Americans get from...
Thanks Mike, I guess it might be a bit early to fully condemn them but your observations makes it less than a rosy outlook. John On Thu, Oct 2, 2008 at 1:40...
Mike Tomas, I seem to stretch my primary chains beyond adjustment in about 8K miles on my 1950 80 chief pulling an Indian side car. Is that normal? I use ...
Hi, lesson learned - never look for cheap source of gears. The cheaper you buy them them the more expensive they are at the end. I was experimenting with them...
Howdy Ron, May not be loading the primary chain equally across its from face inner to outer link runs. If your clutch basket bushing on the trans main shaft is...
Would anybody know the trade number off the tranny bearing that the main shaft rides on. This will be for a 46 chief 3 speed. I had these written down once...
Bill Rowe-Riverview P...
toolroom@...
Oct 2, 2008 2:13 pm
109925
Dirtbag I think a 207 will do I have a Fafnerfull trade # is 6207. Duff ... From: Bill Rowe-Riverview Products <toolroom@...> Subject:...
Most kind Duff, Thank you, Dirtbag g ... From: Terry Duffy To: VirtualIndian@yahoogroups.com Sent: Thursday, October 02, 2008 10:37 AM Subject: Re: [Virtual...
Bill Rowe-Riverview P...
toolroom@...
Oct 2, 2008 2:42 pm
109927
Original fitment was 207 max capacity bearing on the kicker end and 7207 angular contact (thrust) bearing at the clutch side. I believe the bearing that most...
Ron that sure isn't normal for a diamond chain. I have one on my 47 that has about that many miles on it and I'm still waiting for it to loosen up enough to...
bburton
Hayseed@...
Oct 2, 2008 2:47 pm
109929
Does anyone on the list have any information on the schedule for the 2009 Rally in Scotland? It looks like the dates are 24-26 July but I was wondering if...
Thanks John, Would a guy want the Double sealed 6207 for the Kicker end or double shielded. I found the 7207 for clutch side, but have options to chose from on...
Bill Rowe-Riverview P...
toolroom@...
Oct 2, 2008 3:02 pm
109931
use a 6207-2 R/S for both sides. I`ve been running the same bearings since 1987, no problems. IndianFrank ... From: Bill Rowe-Riverview Products...
The sealed bearings should help keep the oil inside, even when using the neopreme outer seal. I personally use the double sealed 6207 but I think the dealer...
Sealed bearings also keep the metal chips out of the bearings. IndianFrank ... From: John Welch <johnmarg2@...> Subject: Re: [Virtual Indian] Tranny...
Thanks Peter, I'll try it. Ron ____________________________________________________________ Click here to find the perfect picture with our powerful photo...
I can't seem to get the site up here in the US. But upon chatting with Allan at D'port, he states that Traquair House is the start, then a tour like the last...
I haven't had any issues with primary chains stretching in any Indian I have owned nor in my 1950 Chief sidecar rig that gets ridden extremely hard. Alignment...
Mike Tomas
bigchief@...
Oct 3, 2008 4:36 am
109938
_________________________________________________________________ Want to do more with Windows Live? Learn “10 hidden secrets” from Jamie. ...
Hi Richard, The link below no longer works. Perchance do you have one that does? Best Regards, Jeff Alperin Cell: 561-449-3063 Web:...
jeff@...
Oct 4, 2008 12:29 pm
109940
Any of the big boys should have one, Stark Kiwi or Greer. Yim [Non-text portions of this message have been removed]...
O1dp00p@...
Oct 4, 2008 1:21 pm
109941
Hi group, I trimed the dist hole (where the wires go in under the cap) so the hole is now a U shape(open at the top) and not a hole anymore. This is so if I...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
