Hi Allan Thank you for your response. I can see why the BHP graph you can produce from block 120 can only really be used on stock engines. Thanks again Rob...
u can only do it when u have throttle by wire no cable. On Mon, Mar 31, 2008 at 9:43 PM, Brent Harris <obrentharris@...> ... [Non-text portions of this...
The accelerator pedal can not be calibrated, no matter if the car has drive by wire or not. You may want to check the factory repair manual for more...
Thanks is correct Br felix Von: VAG-COM@yahoogroups.com [mailto:VAG-COM@yahoogroups.com] Im Auftrag von Sebastian Stange Gesendet: Dienstag, 1. April 2008...
I have been trying to buy CRC industries "mass air flow sensor cleaner" and "throttle body cleaner" in the UK. Can anyone give me a UK supplier. Then I can...
Year 2000 Golf 1.4 petrol - sometimes when the car hits a bump or you slam the door the clentral locking locks the doors. I do not see a fault code right...
Google http://www.ambersil.co.uk/csp/web/Countrypage.CSP?country=GB&lng=3&CSPCHD=00010001000148xz5dSZ002227183660 James ... From: Jonathan Willis To:...
sorry its not an adjustment its a relean for throttle by wire and i have the factory procedures for these cars trucks u name it. im not shure what your reason...
Hi all, Have this passat 1.8L 2000 model,which is experiencing ocassional loss of engine power.I have had the throttle position sensor,fuel pump and throttle...
First I check Wiring to Angle Sensors 1/2 and to Throttle Actuator. OK. Since everthing was ok and the "Angle Sensor 2 for Throttle Actuator (G188) Signal too...
What do you understand by "check wiring"? Did you check the resistance at both ends? Did you check for the WHOLE wiring for bite marks? Did you check the...
I have already spoken to CRC in Somerset and they do not do the MAF or throttle cleaner. Jonathan ... From: J To: VAG-COM@yahoogroups.com Sent: Tuesday, April...
I'm guessing this will work: http://www.ambersil.co.uk/csp/web/ProdDisp.csp?lng=3&country=NO&product=AIR%20SENSOR%20CLEAN&business=AUTOMOTIVE Jess ... ...
Because we are mounting these pedals in a very different vehicle than the one they are designed for we inevitably end up with either less or more pedal travel...
Hello everyone. Can anyone please give me a hand with programing the can-bus for Trailer Hitch on a 2008 Touran. The instuctions for the hitch says.. group 19 ...
Our WIKI has a pretty good explanation for it already... http://wiki.ross-tech.com/index.php/01119 ...so what codes do you have in the transmission control...
Try these instructions... http://wiki.ross-tech.com/index.php/Trailer_Hitch_Retrofitting_(1K) ...and if you are stuck at some point post a complete Auto-Scan...
Yes, I checked the resistance at both ends, spray with WD both ends (throttle side, ECU side), tomorrow I will check for "bite marks" and widened pins. What...
The Readiness Code is a set of 8 bits, each of which corresponds to one monitored emissions "system" in an OBD-II car. When all readiness bits show "Passed",...
I don't think that the vag-com will help you much with this problem. ... lock/latch or maybe the insulation of the wiring between the door and the body is...
... problem. People have misunderstanding that modern diagnostic computer / tools can solve all problems. In fact it can help in way not imagined possible...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
