First thing I would do is to check the soft. coding on the ABS controller. If there's a wrong coding or it's 00000, then you'll get the given DTC's. I've had...
I recode it with program 31 the one the SEAT Ibiza Cupra has it handles a lot better without being too heavy, I recommend to every one with a Polo 9N to do...
I have Vag-Com 409.1 and am trying to fix the locks and lights. Before I took my 2002 Jetta TDI in for service, when you clicked the remote once it unlocked...
I'm gathering that the interior light problem is the switch itself being in the "on" position. There's a three position switch for the light, On w/Doors open,...
Has anyone successfully recoded the tranny and/or engine coding? I've tried the various codes but none work so far. The tranny would be either 0001134 or...
Low voltage (intermittent) is sure to be in the DTC list when you replace a battery. After all, there was low voltage. If they can't clear this....they don't...
Try light switch see if in right position the thing with the locks could be needing setting up go into 46 central con and check setup u should be able to...
... If the engine speed signal were missing a fault code (17748) would have been generated as long as the engine was cranked thru at least two complete...
Hi All, Do I need to re-register HEX-USB interface? I have installed v. 409 on a new computer after the hard drive went or will it self activate one I plug it ...
Hi all, Can anyone recommend / know of an independent VW garage in London. Preferable South East. Many thanks, Woter [Non-text portions of this message have...
woter, ... HEX- (and KEY-) line products carry the registration in the dongle interface and do not require any subsequent activation; they are permanently...
rich herzog
rich@...
Feb 2, 2005 12:31 pm
18625
Hello. I have MFD where was three times wrong code entered, so now it is in safe. I have correct code, but I don't know, how to enter it now. Does anyone know,...
Not that I know of. What they allegedly did was replace the fuel filter and PCV valve. Paul L Fisher 2000 Volkswagen Golf GLS TDI 5 Speed - White - 119,000...
Nope done that. Stays on in 2 of the 3 positions. When you say check the programming, I assume http://www.ross-tech.com/vag-com/cars/vwmkIV.html and then...
... Before digit the code, if the MFD is on desk and non in car, you must verify if the cable called "Code" is wired or is free. If it is free you can not...
... VAG COM won't help with this... If you have it wired up correctly, you can turn it on without the key in the ignition... do this then go watch TV for 1...
Thanks for replay. The MFD is in the car, and cable called "safe" is connected also to +12V. ... From: Claudio Zamagni To: VAg-Com Sent: Wednesday, February...
Re: ABS problems ... common. Pushing the electrical connector one direction or the other (while still plugged in) will often cause the communication to drop ...
Tihol Tiholov
t.tiholov@...
Feb 2, 2005 5:57 pm
18632
Hi Roger. I am dealing with a similar issue with a 2000 1.8 Quattro. I have DTC 65535/ 00-10 which I cannot clear also 00588/74-10 which wont clear. In this...
andrew MOOREY
Andrew@...
Feb 2, 2005 8:30 pm
18633
Thanks Roger, I have purchased a cable and will buy the SW to read and try to re- set the codes myself. Hopefully it is not the code you suggest cannot be...
I think the 65535 number is the correct one for the problem with the airbag computer. It happened on my car too (just came on one day), but it was under...
Assuming that there is airbag coding (hopefully an expert will jump in here)..... VAG Com should be able to read the airbag coding from the airbag controller...
... Hi there, SW London any use? I can HIGHLY recommend these people they are all EX VW/AUDI engineers with at least 40 years experience (combined) They are...
No option avialiable in this combination, sorry. Questions is which is the exact one that is, in theory, able to do comfort via remote? So what part number is...