Does anybody already changed a motor ECU on this type of car ? Does it have channel 50 to learn VIN from Dash ? Does it assume dash LOGIN after this ? Help...
There can be several reasons for this but we still lack detailed information on the other modules in the vehicle in question. An Auto-Scan would partly answer...
Is it possible to change the clock using VAG-COM? On Fri, Jul 24, 2009 at 3:50 AM, Sebastian Stange ... [Non-text portions of this message have been removed]...
The clock you have is is most likely radio controlled... Sebastian Stange Technical Support & Applications Ross-Tech, LLC 881 Sumneytown Pike Lansdale PA...
Sorry for taking a week to get back, Autoscan Saturday,31,October,2009,08:44:24:12705 VCDS Version: Release 908.0 Data version: 20090830 ... Chassis Type: 1J -...
Hi, We have a T5 van 2.5 Tdi 2007 BNZ engine code. It had a faulty exhaust gas pressure sensor G450, This has been replaced and now I need to perform the...
Toby@Nildram
toby@...
Nov 4, 2009 12:36 pm
29964
If the problem is due to a faulty abs ecu i would assume that you could get comms be disconnecting the multiplug from the abs ecu i have seen a similar problem...
The procedure is Ok. 75.3 is Particle Filter Load in %, must be between 15...90 % to perform regeneration. Duty cycle is shown, as standard when there is no...
Cheers Niels, In MVB 075.3 it had a value of 52%, just wanted to check it was in range. I'll get the van back in and give it a try. Toby _____ From:...
Toby@Nildram
toby@...
Nov 5, 2009 8:08 am
29967
Thanks for the replies everyone. I disconnected the ABS ecu this afternoon and I was then able to interrogate any module that I had in the vehicle without...
After performing the forced regenration everything is back to normal. Cheers Niels _____ From: VAG-COM@yahoogroups.com [mailto:VAG-COM@yahoogroups.com] On...
Toby@Nildram
toby@...
Nov 5, 2009 4:44 pm
29969
I have a 2000 Passat, 1.8liter turbo. It keeps coming up with this: Thursday,05,November,2009,11:55:29:56766 VCDS Version: Release 908.1 Victory Auto ...
Just swapped clusters old one burnt badly, Using original keys,original ECU and a second- hand cluster. Chassis Type: 8D - Audi A4 B5 Scan: 01 02 03 08 15...
This can help http://www.ross-tech.com/vag-com/cars/immobilizer.html Regards Baldwin ... From: Zulu Mxolisi <pitstopzulu@...> Subject: [VAG-COM] Swaped...
Based on the test I'm going to replaced the MAF. I am planning on replacing the abs module. I assume this shouldn't have any thing to do with the p1128 code?...
Always check for vacuum leaks first. You might be able to use a length of heater hose to help you listen for leaks along the length of the vacuum hoses. Some...
All the PM is good to start with. Injector seals from this year should probably be replaced too. Leaks aren't usually evident at idle. Your dealer also can...
Customer has asked about their 2008MY TT fitted with halogen lights, to use Scandinavian mode so headlights can be used as day running lights. Under 09 Central...
It does not appear that this module has a provision for dimming the headlight beams, but I'm not that this means they will run at 100% output when used as...
Tks, I enabled Scandinavian mode, the also while in module 09 cent Eletcs, enabled the function which allows DRL to be turned on/off using the MFC via the...
Hello, First here is the full scan log: Friday,06,November,2009,18:24:06:00174 VCDS Version: Release 908.1 Data version: 20091018 ... Chassis Type: 9N - VW...
Thanks for the answer. The problem is that even using the advanced measuring values, I can't find basic channels like requested/actual boost, wg duty...
We are pretty confident that VCDS gives you as much real-time data on these modules as the factory tool does, and in some cases more. However, please post the...
You need to find out a few more bits of information before condemning the #3 injector. Compression; is the coil being fired by the Engine Module; is the ...