Hello Marco, ... At the moment it is only possible to select two definitions. These could contain more than one item each and then it is possible to watch them...
Hello, Changing the baudrate does not make a difference as Unidiag sets the baudrate necessary for communication (normally 10.4kbaud). If the comm port...
Hello, Did you also try another defintion file: AlfaFiatLancia_1924JTD_EDC15C7.def The 2.4 JTD has used different ECUs the first ones responded to address 0x0A...
Hello, According to my information the (german/english) list below is not the correct one for diagnostics via the kwp71 protocol (it might be correct for...
Thank you very much for the information about ABS. At the same I have one question from KWP2000Unidiag. It would be very nice to know what these DTC states...
I would also like to participate on the development but I couldn't find the source codes. It is no problem to disassemble and reverse the code. The protocol...
Hello, Thank you for your support. I tried the AlfaFiatLancia_1924JTD_EDC15C7.def and finally i had right connection but very strange effcts.. I tried other...
Hello Michelangelo, This is not what it should look like. In order to determine what could be going wrong, could you upload or copy paste the iso9141.log file?...
Hello, ... It can also be found the Fiat documentation (pictures other message), but I will try to give a short explanation here. ... This are the four DTC...
Hello Sander, The file log is 146 kb. Hope you can receive the attachment. Or you can find here: http://www.megaupload.com/?d=SJWJICIE Thanks, Best regards. ...
Hello Michelangelo, I received the log file OK. It is also possible to put log files here (maybe better option for the future to prevent large emails to...
Hi Sander just try to switch on "echo" (switched off) but after some seconds hangs down.. even if for few seconds seems works, data correctly received.Put log...
alright guys.. thanks so much for allowing me into ur brilliant group... now on to my issue.. My car (alfa 156 1.8 ts 2000 on x plate)broke down a couple of...
Could you figure out what ECU is in your car? It's most likely a motronic M2.10.4, but it might just be a M1.5.5. Have you tried the unidiag/kwp2000 program? ...
... tried the kwp2000 and couldnt get it working, kept getting an eefface error that drove me nuts.I am probally configuring it wrong... I think it's an M1.5.5...
Do you have one of the cables Sander made? There's a tiny switch inside the big blue plug. If KWP2000 doesn't work with the M1.5.5 you're most likely talking...
... I bought my cable from : http://www.alfaowner.com/Forum/members/sears.html.. I can't see any switch on it.. will pop the cover off later and see if I can...
The cable IS modified to communicate with Airbag & ABS system. The cable IS fully tested for all ECU communications ... From: UniDiag@yahoogroups.com...
... The above post is precisely the reason I bought this cable. The seller comes highly recommended by many of the alfa owner group and seems to have a high...
... A cable that is modified to be able to communicate with both engine ECU and Airbag and/or ABS ECU should normally work. The ECU that is communicated to is...
On Mon, May 4, 2009 at 12:41 PM, bobbypollock73 ... Because the M1.5.5 communicates using the kwp2000 protocol. kwp71 is used if your ecu communicates with...
thanks guys.the mist is clearing... the car is parked 6 miles away so I will go over later and try out the kwp2000 software again.I will post when I,ve done it...
went over to the car this evening and tried the kwp2000 and guess what. yes, it worked...these are the results I got... number of items...2 1. DTC 0x1172,...
1. it tries to adjust fuel mixture but it is not able to optimize it. It's beyond max adjustment. Is your air filter clean? No cracks/bursts in your inlet...
holy ahem, cow... not what I was hoping to hear at all. I will have a look during the week. back to work tommorow.will let u know what if anything I find.....
Hello, The part where communication is running looks normal now. I think the ID is now also read correctly? To keep the communication running for a longer...
Hello, ... 0x1172 = Mixture 1 strength (multiplicative) Multiplicative indicates it goes wrong when under load. ... Besides the sensor itself, it could also...
cheers guys. I am hoping this aint an expensive problem.I have spent far to much time and money on this car already.have done the rear shocks,drop links, 1...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
