Hi Guys, Does any one tell me what is the correct EGR opening value. I found during diagnosis on Unidiag there is oscillate around 32% on the idle gear. I have...
Hello Sander, I have a question. Can i only use your software with your cable or can i also use your written software with an other KKL-usb cable? The cable i...
Hi , I am trying to write a C++ MFC diagnose application for my bosch ECU (DDE 2.1) and I am in trouble. The wake up routine works fine ( Thanks to Andy...
... Hello :). ... At the moment this is not possible, or at least I don't know the command to use for that. Maybe it will be possible in the future. Kind...
Hello Roel, Well, I am sure about the fact that my software works with my cable ... already adapted to also communicate with the Airbag and ABS (and other)...
Hello Alex, This group is not the right location for these questions. I think you better try the opendiag group. But did you already try the KPW71Diag software...
Hello, I can't connect to the car. I get the following message: DebugScreen COM Port opened Init started error rcv wait timeout Init Ready No KeyBytes; Init...
... airbag ... It's done, the airbag bulb is went off with the software of Sander. I'm very happy with it. I have bought a VAG KKL usb cable and have put the ...
Hi , Yes I have tried KWP71Diag and it works fine , but my ECU waits for complement even in the ID Block. But my problem is solved , it was just a timing...
Hi, I tried to connect my JTD engine with Unidiag using the AlfaFiatLancia_19JTD_EDC15.def and an OBD2-KKL RS232 (http://ucables.com/ref/OBD2-KKL); Unidiag...
Hello Cico, ... If I understand it correctly, you are using an USB-COMport adapter? In general this is very tricky, because of the accurate timing required. If...
ID after 5baud init: ID : 9483021620 , 0261203849 ID : 9968537621 , 1267358699 ID : V61 l7.1 33F , F33 1.7l 16V ID : 03262246400ÿ , ÿ00464226230 Read...
Hello, I'm back on the internet. Had some troubles with that. Boban and Cico, is it working for you now? Mine is working fine. Have to press start 2 or 3 times...
... Yes, it's working! :-) ... That was the problem with me... :-( But, sometimes I'm still got an exception error. I think that Sander still have some...
... i ... and ... it ... can ... to make communications between airbag sensor and ECU possible you must have pin 3 and 7 connected in the 16pins connector....
Does anyone have a list of errors for the BS ecu of an Alfa 156. Last night I've connected to the ABS ecu & as a test I plugged out 1 of the sensors: ...
That's nice! Do you confirm Boban you have the same cable as mine? (OBD2-KKL RS232 from ucable) I'll try changing ECU address I'll keep you informed about it. ...
from forum file " Here is a list of codes that I found for the airbag ECU. For whatever reason 0018 is not documented. Some are also hexadecimal. This should...
very sorry, must be for ABS adress ECU is 0x 20 ... Error codes for the ABS control unit Bosch "ABS 5.3" and "ABS 2E": LH = Left Hand/Linke Seite LH = Left...
I've tested the OBD2-KKL cable with Unidiag, using the 0x10 address as adviced; well that's the matter: [...] REI_2000 : ISO code REI_2000 : Tester code ...
Hi there, what com port is the KKL interfac eworking on? EG: com 3 or com 4 etc... this port, com 3, will need to be selected within Unidiag in order to ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
