Hi, I have AR Gtv 2.0 TS (09/1998) and VAG KKL USB cable. I have done small modification and now cable has the switch between pin 3 and 7. The UnidiagKWP2000...
Hi guys, This is john I want some material for KWP2000.. if any one have please send to me.. it will be very useful for me Regards John HCL Tech Thanks &...
John Suresh Kumar Jos...
johnsureshkj@...
Aug 8, 2008 9:47 am
198
I have some information you may find useful on my site. The SSF 14230 standard is based on ISO 14230: ...
Hi I am not able to register in to that website and I am not able to download it... Thanks & Regards JOHN SURESH KUMAR.J From: UniDiag@yahoogroups.com...
John Suresh Kumar Jos...
johnsureshkj@...
Aug 8, 2008 12:17 pm
200
Hello Klaudiusz, The link to the screenshot gives an error. You can also put it in the files section of this group: ...
Hello John, This group is meant to discuss the UniDiag software! If you want info about the kwp2000 protocol, you can look somewhere else e.g. the opendiag...
Hello Hans, According to my information the Stilo 1.9 jtd (8v) can have an edc15c7 or an edc16c39 ECU. Both should be accessed with ECU address 0x10 ! This is...
Hello, That are a lot of faultcodes... According to my info these faultcodes mean: 0x01 Control unit 0x02 Control Unit Power Supply 0x0E Driver's side airbag...
Hi Sander, http://fotogalleria.info/AlfaGtv/kwp71_KF.jpg - now should work. Yes, I use the ECU address for the Airbag 0x00. But finally I've done proper...
Hi, I am troubleshooting overboost issues on a 1.9 JTD multipla with EDC15 ECU. I would like to read the target overboost pressure. But while this item IS in...
Hi, With the EDC15 def file I read very stange temperature readings (airtemperature, watertemperature). Values read big numbers like 330 etc... At first I...
Hi, In the EDC15 file for 1.9JTD the fuel temperature reading is nowhere to be found. Doesn't the ECU report this or is it missing in the DEF file? Does...
Hi, I know that this forum is for discussing the software only, but I hope that there is somebody here who can give me some insight on the following phenomen: ...
Hi Guys, I've been looking high and low for diagnostic software for my alfa 156 2.4 jtd (2002) Would unidiag work with my car? also what cable do i need to...
Hello Speedeprom, Unidiag should be able to communicate with the edc15c2 at ECU address 0x10 and read faultcodes. The data defined in the .def files for the...
Hello Eelco, First thing to check is, if the ISO code returned by the ECU is equal to one of the ISO codes in the header of the .def file you use (open with...
Hello Eelco, It seems there was an error in the file: spaces around a minus sign in both temperature definitions. Because of this, the absolute temp. 273 was...
Thank you very much for reply...!! Many thanks...!!! ... From: Sander To: UniDiag@yahoogroups.com Sent: Tuesday, August 12, 2008 10:24 PM Subject: [UniDiag]...
Hello! I'm a newbie, I joined this group only yesteday. :-) I would like to get diagnosis data from my JTD engine using UniDiag; times ago I tried ELM327 but,...
Hello Sander, First, thanks for the help and the nice program. I think I have a 1.9 JTD 16V (115 Pk)? I used the AlfaFiatLancia_19JTD_EDC15.def file and...
Hello ! I have a Fiat Brava 1,6 16v 1996 without obd connector,just a small connector at engine with 3 wires.Can i connect with Unidiag and a vagcom interface...
Hi all, I was having a lot of trouble to get unidiag to work on my Fiat Stilo. Monday with the help of Eelco I found my cable is fine, my fiat works with...
Well, if you solder it to pin 3 instead of pin 2 it works. How stupid of me. RTFM thy say is it not? Airbags reset. All lights out and go. Tomorrow I will...
Hi Hans, can you tell me which kind of cable did you used for your Stilo JTD? Have you a standard OBD connector or the old 3 pin connector? Thank you so much. ...
Off course, I use this cable: http://ucables.com/ref/OBD2-KKL It works fine, but i must say it was a little corroded on the contacts at first. I just scraped...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
