UniDiag : Messages : 1599-1628 of 1628

Can you connect to your car's ECU?

On Tue, Nov 24, 2009 at 11:50 PM, javier saade <javiersaade@...> wrote:

I dont know what am i doing wrong, but i cant get my alfa 156 selespeed to connect with Unidiag. What are the settings needed? I am using a KKL / rs232 cable.

Those are specific for your KKL/rs232 interface, not for unidiag.

On Mon, Nov 23, 2009 at 11:25 PM, javiersaade <javiersaade@ yahoo.com> wrote:

I have a 2001 Alfa romeo 156 2.0 selespeed. I have a KKL to rs232 cable interface. I cant establish connection with Unidiag, Can somebody please help me and tell me the right configuration to establish connection. I need configurations for comm port 1 which is the serial port of my PC.

Saade

#1627

From: javier saade <javiersaade@...>
Date: Tue Nov 24, 2009 10:50 pm
Subject: Re: Settings

javiersaade

Offline

I dont know what am i doing wrong, but i cant get my alfa 156 selespeed to connect with Unidiag. What are the settings needed? I am using a KKL / rs232 cable.

Those are specific for your KKL/rs232 interface, not for unidiag.

On Mon, Nov 23, 2009 at 11:25 PM, javiersaade <javiersaade@ yahoo.com> wrote:

I have a 2001 Alfa romeo 156 2.0 selespeed. I have a KKL to rs232 cable interface. I cant establish connection with Unidiag, Can somebody please help me and tell me the right configuration to establish connection. I need configurations for comm port 1 which is the serial port of my PC.

Saade

#1626

From: "SE UTV" <serviceengineer@...>
Date: Tue Nov 24, 2009 9:42 pm
Subject: RE: Quick question please

alfenia20l

Offline

inside the interface or at the car's connector, connect pin 7 to pin 1

set ecu to 0x20

protocol to Auto

use KWp71 application

-----Original Message-----
From: UniDiag@yahoogroups.com [mailto:UniDiag@yahoogroups.com] On Behalf Of WhizzMan
Sent: 24 November 2009 20:02
To: UniDiag@yahoogroups.com
Subject: Re: [UniDiag] Quick question please

Not required, but it may help turn error codes into legible descriptions

On Tue, Nov 24, 2009 at 9:00 PM, ctid87 <ctid87@yahoo.co.uk> wrote:

Do I need to load any def file to access the airbag ECU on 2001 147?

Thanks very much

#1625

From: WhizzMan <whizzman@...>
Date: Tue Nov 24, 2009 8:02 pm
Subject: Re: Quick question please

whuizzman1970

Offline

Not required, but it may help turn error codes into legible descriptions

On Tue, Nov 24, 2009 at 9:00 PM, ctid87 <ctid87@...> wrote:

Do I need to load any def file to access the airbag ECU on 2001 147?

Thanks very much

#1624

From: "ctid87" <ctid87@...>
Date: Tue Nov 24, 2009 8:00 pm
Subject: Quick question please

ctid87

Offline

Do I need to load any def file to access the airbag ECU on 2001 147?

Thanks very much

#1623

From: "ruessel.rudolf" <ruessel.rudolf@...>
Date: Tue Nov 24, 2009 12:05 pm
Subject: Three unclear items in UniDiagKWP2000_0_4_0_3

ruessel.rudolf

Offline

Hello all,

I downloaded the files, connected to the car (Marea 1.6) and all worked fine.
Then I started to translate the .def-file into german because I'm german and
it's much easier for me if the items appear in that language.

Most items i was able to translate but at these three I don't understand what
the meaning is.

Would it be possible to you to give me an explanation what these following
means? - If I know what kind of information the item shows I can translate it.

1st.
What is ment with "Throttle Repeater"? What does this in a car? - How can I
repeat a throttle?

2nd.
What does "Power-latch duration" say to me? - The only thing I can imagine - but
not believe - is that this could show how long I started with the start-key
(ignition). But is this true?

3rd.
And then the items "Coil 1 charge time" and "Coil 2 charge time".
What is a coil? why is it charged? what is normal then?

The last question is if I should upload the german definition-file after I have
finished creating it?
Does this bring benefit to you or is it uninteressting?

Sorry about my awful english but I hope you'd understand what I ment.

Thanks in advance.

Best regards

Rudolf

#1622

From: WhizzMan <whizzman@...>
Date: Tue Nov 24, 2009 9:04 am
Subject: Re: Settings

whuizzman1970

Offline

Those are specific for your KKL/rs232 interface, not for unidiag.

On Mon, Nov 23, 2009 at 11:25 PM, javiersaade <javiersaade@...> wrote:

I have a 2001 Alfa romeo 156 2.0 selespeed. I have a KKL to rs232 cable interface. I cant establish connection with Unidiag, Can somebody please help me and tell me the right configuration to establish connection. I need configurations for comm port 1 which is the serial port of my PC.

Saade

#1621

From: "fbenzouzi" <fbenzouzi@...>
Date: Tue Nov 24, 2009 12:37 am
Subject: settings cable kkl usb

fbenzouzi

Offline

hi,
i have a cable kkl usb and i don't know how i can configure my com port!can you
help me plz?
car : alfa 156 2,4JTD 99 EDC15c5

thks

#1620

From: "javiersaade" <javiersaade@...>
Date: Mon Nov 23, 2009 10:25 pm
Subject: Settings

javiersaade

Offline

I have a 2001 Alfa romeo 156 2.0 selespeed. I have a KKL to rs232 cable
interface. I cant establish connection with Unidiag, Can somebody please help me
and tell me the right configuration to establish connection. I need
configurations for comm port 1 which is the serial port of my PC.

Saade

#1619

From: "danilo_papa" <mail@...>
Date: Sun Nov 22, 2009 11:53 am
Subject: Re: DTCs on Fiat Punto 188 and general DTC Reference

danilo_papa

Offline

Great! Now I understand! Thanks

--- In UniDiag@yahoogroups.com, WhizzMan <whizzman@...> wrote:
>
> Ah, so there is an extra base value that you have to subtract to get the
> various group DTCs.
>
> Subtract 0x4000 for frame, 0x8000 for body and 0xC000 for communications
>
> On Sat, Nov 21, 2009 at 6:51 PM, beppe_m69 <beppe_m69@...> wrote:
>
> >
> >
> >
> >
> > --- In UniDiag@yahoogroups.com <UniDiag%40yahoogroups.com>, "danilo_papa"
> > <mail@> wrote:
> > >
> > > Thanks!!!
> > > And how can I convert the DTCs? E.g. from 0xD702 to U1702?
> > > D stands for U1?! And no character only numbers mean P errors?
> > >
> > > --- In UniDiag@yahoogroups.com <UniDiag%40yahoogroups.com>, "beppe_m69"
> > <beppe_m69@> wrote:
> > > >
> > > >
> > > >
> > > > --- In UniDiag@yahoogroups.com <UniDiag%40yahoogroups.com>,
> > "danilo_papa" <mail@> wrote:
> > > > >
> > > > > Hey folks,
> > > > > I got two errors on my sisters Punto. It's an 188 '01 1.2 16V.
> > > > > The DTCs are 0xD702 and 0x1135. Has anyone a desription for them?
> > > > > And one question in general: When I look for OBD troublecodes
> > reference tables on the net, I only find references for codes like Pxxx,
> > Cxxx, etc. The codes Unidiag uses start with 0x, so they seem to be hex
> > codes, is that correct? Is there any possibility to convert them to the
> > common ones to discover their reason? If not, where can I find their
> > description?
> > > > >
> > > > > Kind regards
> > > > >
> > > > > Danilo
> > > > >
> > > >
> > > >
> > > > DTC:
> > > > 0xD702 = U1702 Communication CAN pilot electric steering(EPS)
> > > > 0x1135 = P1135 Oxygen sensor Bank1-Sensor2
> > > >
> > > > excuse for my English, not he speak!
> > > >
> > > > Kind regards
> > > >
> > > > Beppe
> > > >
> > >
> > My example converter DTC for UniDiag:
> > 0x0101 = P0101 (I check engine/traction)
> > 0x1200 = P1200
> > 0x2020 = P2020
> > 0x3434 = P3434
> >
> > 0x4108 = C0108 (Frame)
> > 0x5999 = C1999
> > 0x6598 = C2598
> > 0x7040 = C3040
> >
> > 0x8224 = B0224 (Body)
> > 0x9177 = B1177
> > 0xA085 = B2085
> > 0xB134 = B3134
> >
> > 0xC145 = U0145 (Communication)
> > 0xD600 = U1600
> > 0xE354 = U2354
> > 0xF899 = U3899
> >
> >
> >
>

#1618

From: WhizzMan <whizzman@...>
Date: Sun Nov 22, 2009 8:36 am
Subject: Re: Re: DTCs on Fiat Punto 188 and general DTC Reference

whuizzman1970

Offline

Ah, so there is an extra base value that you have to subtract to get the various group DTCs.

Subtract 0x4000 for frame, 0x8000 for body and 0xC000 for communications

On Sat, Nov 21, 2009 at 6:51 PM, beppe_m69 <beppe_m69@...> wrote:

--- In UniDiag@yahoogroups.com, "danilo_papa" <mail@...> wrote:
>
> Thanks!!!
> And how can I convert the DTCs? E.g. from 0xD702 to U1702?
> D stands for U1?! And no character only numbers mean P errors?
>
> --- In UniDiag@yahoogroups.com, "beppe_m69" <beppe_m69@> wrote:
> >
> >
> >
> > --- In UniDiag@yahoogroups.com, "danilo_papa" <mail@> wrote:
> > >
> > > Hey folks,
> > > I got two errors on my sisters Punto. It's an 188 '01 1.2 16V.
> > > The DTCs are 0xD702 and 0x1135. Has anyone a desription for them?
> > > And one question in general: When I look for OBD troublecodes reference tables on the net, I only find references for codes like Pxxx, Cxxx, etc. The codes Unidiag uses start with 0x, so they seem to be hex codes, is that correct? Is there any possibility to convert them to the common ones to discover their reason? If not, where can I find their description?
> > >
> > > Kind regards
> > >
> > > Danilo
> > >
> >
> >
> > DTC:
> > 0xD702 = U1702 Communication CAN pilot electric steering(EPS)
> > 0x1135 = P1135 Oxygen sensor Bank1-Sensor2
> >
> > excuse for my English, not he speak!
> >
> > Kind regards
> >
> > Beppe
> >
>
My example converter DTC for UniDiag:
0x0101 = P0101 (I check engine/traction)
0x1200 = P1200
0x2020 = P2020
0x3434 = P3434

0x4108 = C0108 (Frame)
0x5999 = C1999
0x6598 = C2598
0x7040 = C3040

0x8224 = B0224 (Body)
0x9177 = B1177
0xA085 = B2085
0xB134 = B3134

0xC145 = U0145 (Communication)
0xD600 = U1600
0xE354 = U2354
0xF899 = U3899

#1617

From: "beppe_m69" <beppe_m69@...>
Date: Sat Nov 21, 2009 5:51 pm
Subject: Re: DTCs on Fiat Punto 188 and general DTC Reference

beppe_m69

Offline

--- In UniDiag@yahoogroups.com, "danilo_papa" <mail@...> wrote:
>
> Thanks!!!
> And how can I convert the DTCs? E.g. from 0xD702 to U1702?
> D stands for U1?! And no character only numbers mean P errors?
>
> --- In UniDiag@yahoogroups.com, "beppe_m69" <beppe_m69@> wrote:
> >
> >
> >
> > --- In UniDiag@yahoogroups.com, "danilo_papa" <mail@> wrote:
> > >
> > > Hey folks,
> > > I got two errors on my sisters Punto. It's an 188 '01 1.2 16V.
> > > The DTCs are 0xD702 and 0x1135. Has anyone a desription for them?
> > > And one question in general: When I look for OBD troublecodes reference
tables on the net, I only find references for codes like Pxxx, Cxxx, etc. The
codes Unidiag uses start with 0x, so they seem to be hex codes, is that correct?
Is there any possibility to convert them to the common ones to discover their
reason? If not, where can I find their description?
> > >
> > > Kind regards
> > >
> > > Danilo
> > >
> >
> >
> > DTC:
> > 0xD702 = U1702 Communication CAN pilot electric steering(EPS)
> > 0x1135 = P1135 Oxygen sensor Bank1-Sensor2
> >
> > excuse for my English, not he speak!
> >
> > Kind regards
> >
> > Beppe
> >
>
My example converter DTC for UniDiag:
0x0101 = P0101 (I check engine/traction)
0x1200 = P1200
0x2020 = P2020
0x3434 = P3434

0x4108 = C0108 (Frame)
0x5999 = C1999
0x6598 = C2598
0x7040 = C3040

0x8224 = B0224 (Body)
0x9177 = B1177
0xA085 = B2085
0xB134 = B3134

0xC145 = U0145 (Communication)
0xD600 = U1600
0xE354 = U2354
0xF899 = U3899

#1616

From: "danilo_papa" <mail@...>
Date: Sat Nov 21, 2009 3:57 pm
Subject: Re: DTCs on Fiat Punto 188 and general DTC Reference

danilo_papa

Offline

Thanks!!!
And how can I convert the DTCs? E.g. from 0xD702 to U1702?
D stands for U1?! And no character only numbers mean P errors?

--- In UniDiag@yahoogroups.com, "beppe_m69" <beppe_m69@...> wrote:
>
>
>
> --- In UniDiag@yahoogroups.com, "danilo_papa" <mail@> wrote:
> >
> > Hey folks,
> > I got two errors on my sisters Punto. It's an 188 '01 1.2 16V.
> > The DTCs are 0xD702 and 0x1135. Has anyone a desription for them?
> > And one question in general: When I look for OBD troublecodes reference
tables on the net, I only find references for codes like Pxxx, Cxxx, etc. The
codes Unidiag uses start with 0x, so they seem to be hex codes, is that correct?
Is there any possibility to convert them to the common ones to discover their
reason? If not, where can I find their description?
> >
> > Kind regards
> >
> > Danilo
> >
>
>
> DTC:
> 0xD702 = U1702 Communication CAN pilot electric steering(EPS)
> 0x1135 = P1135 Oxygen sensor Bank1-Sensor2
>
> excuse for my English, not he speak!
>
> Kind regards
>
> Beppe
>

#1615

From: "beppe_m69" <beppe_m69@...>
Date: Fri Nov 20, 2009 8:55 pm
Subject: Re: DTCs on Fiat Punto 188 and general DTC Reference

beppe_m69

Offline

--- In UniDiag@yahoogroups.com, "danilo_papa" <mail@...> wrote:
>
> Hey folks,
> I got two errors on my sisters Punto. It's an 188 '01 1.2 16V.
> The DTCs are 0xD702 and 0x1135. Has anyone a desription for them?
> And one question in general: When I look for OBD troublecodes reference tables
on the net, I only find references for codes like Pxxx, Cxxx, etc. The codes
Unidiag uses start with 0x, so they seem to be hex codes, is that correct? Is
there any possibility to convert them to the common ones to discover their
reason? If not, where can I find their description?
>
> Kind regards
>
> Danilo
>


DTC:
0xD702 = U1702 Communication CAN pilot electric steering(EPS)
0x1135 = P1135 Oxygen sensor Bank1-Sensor2

excuse for my English, not he speak!

Kind regards

Beppe

#1614

From: "menke_2005" <yahoo@...>
Date: Fri Nov 20, 2009 6:10 pm
Subject: KWP2000 on motorcycle ECU

menke_2005

Offline

I'm trying to connect to my Motorcycle ECU, and have had limited success.

It responds to a KWP2000 fast init, but then I cannot get any other response -


Tester - 0x81 0x12 0xf1 0x81 0x05
ECU - 0x80 0xf1 0x12 0x03 0xc1 0xea 0x8f 0xc0

From here I try both 3 and 4 byte headers, but no response, even to "Tester
Present" or other requests.

Any ideas?

#1613

From: "danilo_papa" <mail@...>
Date: Fri Nov 20, 2009 3:25 pm
Subject: DTCs on Fiat Punto 188 and general DTC Reference

danilo_papa

Offline

Hey folks,
I got two errors on my sisters Punto. It's an 188 '01 1.2 16V.
The DTCs are 0xD702 and 0x1135. Has anyone a desription for them?
And one question in general: When I look for OBD troublecodes reference tables
on the net, I only find references for codes like Pxxx, Cxxx, etc. The codes
Unidiag uses start with 0x, so they seem to be hex codes, is that correct? Is
there any possibility to convert them to the common ones to discover their
reason? If not, where can I find their description?

Kind regards

Danilo

#1612

From: "ccost1974" <ccost1974@...>
Date: Fri Nov 20, 2009 10:30 am
Subject: punto 1.2 16V

ccost1974

Offline

Hello everybody
i have a problem with Dtc in my punto
i try to use a KKL USB adapter and unidiag
i set to port 4 9600
with "fast init" setting enable i cannot get communication with ECU
if i select "5 baud init" i get KeyWord received 8FEF 2031
but after some second i get "error rcv wait timeout"
if I deselect "Echo after send" i get also 8FEF  2031 communication remain
active but i get message data shorter then description
i use FiatLancia_1216V_ME73H4.def (my ECU is M73H4)
thanks for any help

#1611

From: "Juri" <zatoi4i007@...>
Date: Wed Nov 18, 2009 12:47 pm
Subject: Re: ABS error 0x5276

zatoi4i007

Offline

Ok,thanks. I tray the traditional diagnosting - searching the earth and so on
and so on...
Anyway, the car is stil moving without ABS and cruise control)))

--- In UniDiag@yahoogroups.com, WhizzMan <whizzman@...> wrote:
>
> The communications error while doing diag is normal. The Dash uses the same
> "channel" as the diag. No info on the 0x5276 tho, sorry.
>
>
> On Tue, Nov 17, 2009 at 4:48 PM, Juri <zatoi4i007@...> wrote:
>
> >
> >
> > Hi,
> > I have Alfa 156 2.4 JTD 04/2002, 150 hP, Bosch ABS 5.7 with VDC.
> >
> > Recently in my Alfa gone ABS, VDC and Cruise Control, but without
> > warning messages on central panel.
> >
> > I test ABS with UniDiag 2000 and get unknow error 0x5276.
> > Also, while UniDiag communicating with ABS system, central panel start
> > beeping and showing ABS SYSTEM FAILURE and VDC SYSTEM FAILURE.
> >
> > Any ideas what it would be?
> >
> >
> >
>

#1610

From: "kiepas96" <kiepas96@...>
Date: Tue Nov 17, 2009 9:07 pm
Subject: Re: help with kwmp71 alfa 156 1.8 TS (1998)

kiepas96

Offline

Problem is solved by changing ecu. Thx 4 help!!

--- In UniDiag@yahoogroups.com, "kiepas96" <kiepas96@...> wrote:
>
> Hi, i cannot connect to airbag ecu, i tried many combinations of settings,
also tried on two computers. Heres what kwmp71 is saying:
> m155 and abs ecu are working. Cable is checked. Sorry for my bad english
>
> COM Port opened
> Init started
> Init Ready
> KeyBytes, count : 5
> A7
> 86
> 02
> 97
> 9B
> error rcv wait timeout
> ID after 5baud init:
> no data received
> Error in Communication
>
> Please help me
>

#1609

From: WhizzMan <whizzman@...>
Date: Tue Nov 17, 2009 5:38 pm
Subject: Re: ABS error 0x5276

whuizzman1970

Offline

The communications error while doing diag is normal. The Dash uses the same "channel" as the diag. No info on the 0x5276 tho, sorry.

On Tue, Nov 17, 2009 at 4:48 PM, Juri <zatoi4i007@...> wrote:

Hi,
I have Alfa 156 2.4 JTD 04/2002, 150 hP, Bosch ABS 5.7 with VDC.

Recently in my Alfa gone ABS, VDC and Cruise Control, but without
warning messages on central panel.

I test ABS with UniDiag 2000 and get unknow error 0x5276.
Also, while UniDiag communicating with ABS system, central panel start
beeping and showing ABS SYSTEM FAILURE and VDC SYSTEM FAILURE.

Any ideas what it would be?

#1608

From: "Juri" <zatoi4i007@...>
Date: Tue Nov 17, 2009 3:48 pm
Subject: ABS error 0x5276

zatoi4i007

Offline

Hi,
   I have Alfa 156 2.4 JTD 04/2002,  150 hP, Bosch ABS 5.7 with VDC.

Recently  in my Alfa gone ABS, VDC and Cruise Control, but without
warning messages on central panel.

I test ABS with UniDiag 2000 and get unknow error 0x5276.
Also, while UniDiag communicating with ABS system, central panel start
beeping and showing ABS SYSTEM FAILURE and VDC SYSTEM FAILURE.

Any ideas what it would be?

#1607

From: WhizzMan <whizzman@...>
Date: Sun Nov 15, 2009 6:57 pm
Subject: Re: Error in Alfa 156 1.6 ts

whuizzman1970

Offline

It means it is trying to correct your mixture, but even at maximal correction, it doesn't work. The most common cause for this is a worn MAF sensor. They can be replaced by either the OEM part, some brandless chinese sensor, or a replacement sensor from Pierburg. I and many others (also VW and Mercedes mechanics) have found the Pierburg sensors a very good replacement that usually lasts longer than the OEM sensor.

On Sun, Nov 15, 2009 at 2:28 PM, antoniosk <antoniosk@...> wrote:

I checkjed my alfa and I have the following error.

P1172

Failed Component Code: Self adaptation parameters TRA
Fault Symptom: Below Minimum Limit
Warning Lamp Status: Warning Lamp not Illuminated
Fault Test State: Test complete for this Error or not applicable.
Fault Code Storage State: Error Present at time of request
Event Count: 64 count
Filter Count: 0 count
Environmental Condition One: Engine Speed: 920 rpm
Environmental Condition Two: Engine Coolant Temp: 75.3 °C

I am erasing it but when the engine isrunning then is comming again.

The above is with alfadiag, but unidiag gives the same error P1172.

Does someone can understand what this error is about and how I can fix it??

#1606

From: "antoniosk" <antoniosk@...>
Date: Sun Nov 15, 2009 1:28 pm
Subject: Error in Alfa 156 1.6 ts

antoniosk

Offline

I checkjed my alfa and I have the following error.

P1172

Failed Component Code: Self adaptation parameters TRA
Fault Symptom: Below Minimum Limit
Warning Lamp Status: Warning Lamp not Illuminated
Fault Test State: Test complete for this Error or not applicable.
Fault Code Storage State: Error Present at time of request
Event Count: 64 count
Filter Count: 0 count
Environmental Condition One: Engine Speed: 920 rpm
Environmental Condition Two: Engine Coolant Temp: 75.3 °C

I am erasing it but when the engine isrunning then is comming again.

The above is with alfadiag, but unidiag gives the same error P1172.

Does someone can understand what this error is about and how I can fix it??

#1605

From: messaoudene karim <smartmars13@...>
Date: Sat Nov 14, 2009 2:03 pm
Subject: Re : Unidiag KWP71 / KWP81

smartmars13

Offline

De: teki99t205 <spairo1741@...>
Objet: [UniDiag] Unidiag KWP71 / KWP81
Ã€: UniDiag@yahoogroups.com
Date: Samedi 14 Novembre 2009, 14h46

pls anyone tell me where is this software : Unidiag KWP71 / KWP81

--
[URL=http://img23. imageshack. us/i/unidiagkwp7 181.jpg/][IMG]http://img23. imageshack. us/img23/ 3962/unidiagkwp7 181.th.jpg[/IMG][/URL]

--
[url=http://img23. imageshack. us/i/unidiagkwp7 181.jpg/][img=http://img23. imageshack. us/img23/ 3962/unidiagkwp7 181.th.jpg][/url]

#1604

From: "teki99t205" <spairo1741@...>
Date: Sat Nov 14, 2009 1:46 pm
Subject: Unidiag KWP71 / KWP81

teki99t205

Offline

pls anyone tell me where is this software : Unidiag KWP71 / KWP81

--
[URL=http://img23.imageshack.us/i/unidiagkwp7181.jpg/][IMG]http://img23.imagesha\
ck.us/img23/3962/unidiagkwp7181.th.jpg[/IMG][/URL]

--
[url=http://img23.imageshack.us/i/unidiagkwp7181.jpg/][img=http://img23.imagesha\
ck.us/img23/3962/unidiagkwp7181.th.jpg][/url]

#1603

From: "kkosir19" <amdbrutale@...>
Date: Mon Nov 9, 2009 9:53 am
Subject: Re: Airbag reset for Alfa Romeo 147

kkosir19

Offline

Please help me in this matter my airbag light is getting on my nerves.







--- In UniDiag@yahoogroups.com, "kkosir19" <amdbrutale@...> wrote:
>
> Hi,
>
> i have a Alfa Romeo 147 1.6ts ECO year 2001. Last week my airbag light has
come on.
> The same thing has happened before (aprox. 1 year ago) than i took the car on
service and they just erased the error and the light disapered ( i payed 20
euros for erasing the problem). The problem was that sometimes connector for
airbag under the passanger seat loses connection. How can i erase airbag error.
Where can i geat the cheapest obd cable, software? I have newer laptop computer
with usb and win XP professional.
> Please guide from step to step.
>
>
> Thanks,
>    Klemen
>

#1602

From: "SE UTV" <serviceengineer@...>
Date: Sun Nov 8, 2009 7:11 pm
Subject: RE: Re: help with kwmp71 alfa 156 1.8 TS (1998)

alfenia20l

Offline

meant to type airbag ...... not abs

been a '98 it may have an AIRBAG system that is not kwp71 compatible

-----Original Message-----
From: UniDiag@yahoogroups.com [mailto:UniDiag@yahoogroups.com] On Behalf Of kiepas96
Sent: 08 November 2009 12:08
To: UniDiag@yahoogroups.com
Subject: [UniDiag] Re: help with kwmp71 alfa 156 1.8 TS (1998)

i cant connect to airbag not abs!!

--- In UniDiag@yahoogroups.com, "SE UTV" <serviceengineer@...> wrote:
>
> Being a '98 car it may have any earlier abs system which is not KWP71
> protocol.
>
> -----Original Message-----
> From: UniDiag@yahoogroups.com [mailto:UniDiag@yahoogroups.com] On Behalf
> Of kiepas96
> Sent: 08 November 2009 09:13
> To: UniDiag@yahoogroups.com
> Subject: [UniDiag] Re: help with kwmp71 alfa 156 1.8 TS (1998)
>
>
>
>
>
>
> --- In UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com, "SE
> UTV" <serviceengineer@> wrote:
> >
> > ooopphss.... airbag.... yes KWP71 is the correct software
> >
> > change the following parameters:
> >
> > ECU address to 0x00
> > Protocol to KWP71???
> >
>
> checked
>
> > 1st is your cable modified?
> >
> > if not solder pin 7 to pin 3 internally of the interface
>
> yes is modified, i can connect to ecu and abs ecu
> >
> >
> >
> > -----Original Message-----
> > From: UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com
> [mailto:UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com] On
> Behalf
> > Of kiepas96
> > Sent: 07 November 2009 15:04
> > To: UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com
> > Subject: [UniDiag] Re: help with kwmp71 alfa 156 1.8 TS (1998)
> >
> >
> >
> >
> > how do i use unidiag to read dtc codes from airbag?
> >
> > --- In UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com,
> "SE
> > UTV" <serviceengineer@> wrote:
> > >
> > > you should be using UniDiag software with the associated M1.5.5 def
> > file
> > >
> > > -----Original Message-----
> > > From: UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com
> > [mailto:UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com]
> On
> > Behalf
> > > Of kiepas96
> > > Sent: 06 November 2009 19:11
> > > To: UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com
> > > Subject: [UniDiag] help with kwmp71 alfa 156 1.8 TS (1998)
> > >
> > >
> > >
> > >
> > > Hi, i cannot connect to airbag ecu, i tried many combinations of
> > > settings, also tried on two computers. Heres what kwmp71 is saying:
> > > m155 and abs ecu are working. Cable is checked. Sorry for my bad
> > english
> > >
> > > COM Port opened
> > > Init started
> > > Init Ready
> > > KeyBytes, count : 5
> > > A7
> > > 86
> > > 02
> > > 97
> > > 9B
> > > error rcv wait timeout
> > > ID after 5baud init:
> > > no data received
> > > Error in Communication
> > >
> > > Please help me
> > >
> > >
> > >
> > >
> > >
> > >
> > > __________ Information from ESET Smart Security, version of virus
> > > signature database 4580 (20091106) __________
> > >
> > > The message was checked by ESET Smart Security.
> > >
> > > http://www.eset. <http://www.eset. <http://www.eset.com> com> com
> > >
> >
> >
> >
> >
> >
> >
> > __________ Information from ESET Smart Security, version of virus
> > signature database 4582 (20091107) __________
> >
> > The message was checked by ESET Smart Security.
> >
> > http://www.eset. <http://www.eset.com> com
> >
>
>
>
>
>
>
> __________ Information from ESET Smart Security, version of virus
> signature database 4582 (20091107) __________
>
> The message was checked by ESET Smart Security.
>
> http://www.eset.com
>

__________ Information from ESET Smart Security, version of virus signature database 4584 (20091108) __________

The message was checked by ESET Smart Security.

http://www.eset.com

#1601

From: "kiepas96" <kiepas96@...>
Date: Sun Nov 8, 2009 12:08 pm
Subject: Re: help with kwmp71 alfa 156 1.8 TS (1998)

kiepas96

Offline

i cant connect to airbag not abs!!


--- In UniDiag@yahoogroups.com, "SE UTV" <serviceengineer@...> wrote:
>
> Being a '98 car it may have any earlier abs system which is not KWP71
> protocol.
>
> -----Original Message-----
> From: UniDiag@yahoogroups.com [mailto:UniDiag@yahoogroups.com] On Behalf
> Of kiepas96
> Sent: 08 November 2009 09:13
> To: UniDiag@yahoogroups.com
> Subject: [UniDiag] Re: help with kwmp71 alfa 156 1.8 TS (1998)
>
>
>
>
>
>
> --- In UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com, "SE
> UTV" <serviceengineer@> wrote:
> >
> > ooopphss.... airbag.... yes KWP71 is the correct software
> >
> > change the following parameters:
> >
> > ECU address to 0x00
> > Protocol to KWP71???
> >
>
> checked
>
> > 1st is your cable modified?
> >
> > if not solder pin 7 to pin 3 internally of the interface
>
> yes is modified, i can connect to ecu and abs ecu
> >
> >
> >
> > -----Original Message-----
> > From: UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com
> [mailto:UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com] On
> Behalf
> > Of kiepas96
> > Sent: 07 November 2009 15:04
> > To: UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com
> > Subject: [UniDiag] Re: help with kwmp71 alfa 156 1.8 TS (1998)
> >
> >
> >
> >
> > how do i use unidiag to read dtc codes from airbag?
> >
> > --- In UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com,
> "SE
> > UTV" <serviceengineer@> wrote:
> > >
> > > you should be using UniDiag software with the associated M1.5.5 def
> > file
> > >
> > > -----Original Message-----
> > > From: UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com
> > [mailto:UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com]
> On
> > Behalf
> > > Of kiepas96
> > > Sent: 06 November 2009 19:11
> > > To: UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com
> > > Subject: [UniDiag] help with kwmp71 alfa 156 1.8 TS (1998)
> > >
> > >
> > >
> > >
> > > Hi, i cannot connect to airbag ecu, i tried many combinations of
> > > settings, also tried on two computers. Heres what kwmp71 is saying:
> > > m155 and abs ecu are working. Cable is checked. Sorry for my bad
> > english
> > >
> > > COM Port opened
> > > Init started
> > > Init Ready
> > > KeyBytes, count : 5
> > > A7
> > > 86
> > > 02
> > > 97
> > > 9B
> > > error rcv wait timeout
> > > ID after 5baud init:
> > > no data received
> > > Error in Communication
> > >
> > > Please help me
> > >
> > >
> > >
> > >
> > >
> > >
> > > __________ Information from ESET Smart Security, version of virus
> > > signature database 4580 (20091106) __________
> > >
> > > The message was checked by ESET Smart Security.
> > >
> > > http://www.eset. <http://www.eset. <http://www.eset.com> com> com
> > >
> >
> >
> >
> >
> >
> >
> > __________ Information from ESET Smart Security, version of virus
> > signature database 4582 (20091107) __________
> >
> > The message was checked by ESET Smart Security.
> >
> > http://www.eset. <http://www.eset.com> com
> >
>
>
>
>
>
>
> __________ Information from ESET Smart Security, version of virus
> signature database 4582 (20091107) __________
>
> The message was checked by ESET Smart Security.
>
> http://www.eset.com
>

#1600

From: "SE UTV" <serviceengineer@...>
Date: Sun Nov 8, 2009 10:54 am
Subject: RE: Re: help with kwmp71 alfa 156 1.8 TS (1998)

alfenia20l

Offline

Being a '98 car it may have any earlier abs system which is not KWP71 protocol.

-----Original Message-----
From: UniDiag@yahoogroups.com [mailto:UniDiag@yahoogroups.com] On Behalf Of kiepas96
Sent: 08 November 2009 09:13
To: UniDiag@yahoogroups.com
Subject: [UniDiag] Re: help with kwmp71 alfa 156 1.8 TS (1998)

--- In UniDiag@yahoogroups.com, "SE UTV" <serviceengineer@...> wrote:
>
> ooopphss.... airbag.... yes KWP71 is the correct software
>
> change the following parameters:
>
> ECU address to 0x00
> Protocol to KWP71???
>

checked

> 1st is your cable modified?
>
> if not solder pin 7 to pin 3 internally of the interface

yes is modified, i can connect to ecu and abs ecu
>
>
>
> -----Original Message-----
> From: UniDiag@yahoogroups.com [mailto:UniDiag@yahoogroups.com] On Behalf
> Of kiepas96
> Sent: 07 November 2009 15:04
> To: UniDiag@yahoogroups.com
> Subject: [UniDiag] Re: help with kwmp71 alfa 156 1.8 TS (1998)
>
>
>
>
> how do i use unidiag to read dtc codes from airbag?
>
> --- In UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com, "SE
> UTV" <serviceengineer@> wrote:
> >
> > you should be using UniDiag software with the associated M1.5.5 def
> file
> >
> > -----Original Message-----
> > From: UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com
> [mailto:UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com] On
> Behalf
> > Of kiepas96
> > Sent: 06 November 2009 19:11
> > To: UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com
> > Subject: [UniDiag] help with kwmp71 alfa 156 1.8 TS (1998)
> >
> >
> >
> >
> > Hi, i cannot connect to airbag ecu, i tried many combinations of
> > settings, also tried on two computers. Heres what kwmp71 is saying:
> > m155 and abs ecu are working. Cable is checked. Sorry for my bad
> english
> >
> > COM Port opened
> > Init started
> > Init Ready
> > KeyBytes, count : 5
> > A7
> > 86
> > 02
> > 97
> > 9B
> > error rcv wait timeout
> > ID after 5baud init:
> > no data received
> > Error in Communication
> >
> > Please help me
> >
> >
> >
> >
> >
> >
> > __________ Information from ESET Smart Security, version of virus
> > signature database 4580 (20091106) __________
> >
> > The message was checked by ESET Smart Security.
> >
> > http://www.eset. <http://www.eset.com> com
> >
>
>
>
>
>
>
> __________ Information from ESET Smart Security, version of virus
> signature database 4582 (20091107) __________
>
> The message was checked by ESET Smart Security.
>
> http://www.eset.com
>

__________ Information from ESET Smart Security, version of virus signature database 4582 (20091107) __________

The message was checked by ESET Smart Security.

http://www.eset.com

#1599

From: "kiepas96" <kiepas96@...>
Date: Sun Nov 8, 2009 9:12 am
Subject: Re: help with kwmp71 alfa 156 1.8 TS (1998)

kiepas96

Offline

--- In UniDiag@yahoogroups.com, "SE UTV" <serviceengineer@...> wrote:
>
> ooopphss.... airbag.... yes KWP71 is the correct software
>
> change the following parameters:
>
> ECU address to 0x00
> Protocol to KWP71???
>

checked

> 1st is your cable modified?
>
> if not solder pin 7 to pin 3 internally of the interface

yes is modified, i can connect to ecu and abs ecu
>
>
>
> -----Original Message-----
> From: UniDiag@yahoogroups.com [mailto:UniDiag@yahoogroups.com] On Behalf
> Of kiepas96
> Sent: 07 November 2009 15:04
> To: UniDiag@yahoogroups.com
> Subject: [UniDiag] Re: help with kwmp71 alfa 156 1.8 TS (1998)
>
>
>
>
> how do i use unidiag to read dtc codes from airbag?
>
> --- In UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com, "SE
> UTV" <serviceengineer@> wrote:
> >
> > you should be using UniDiag software with the associated M1.5.5 def
> file
> >
> > -----Original Message-----
> > From: UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com
> [mailto:UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com] On
> Behalf
> > Of kiepas96
> > Sent: 06 November 2009 19:11
> > To: UniDiag@yahoogroups <mailto:UniDiag%40yahoogroups.com> .com
> > Subject: [UniDiag] help with kwmp71 alfa 156 1.8 TS (1998)
> >
> >
> >
> >
> > Hi, i cannot connect to airbag ecu, i tried many combinations of
> > settings, also tried on two computers. Heres what kwmp71 is saying:
> > m155 and abs ecu are working. Cable is checked. Sorry for my bad
> english
> >
> > COM Port opened
> > Init started
> > Init Ready
> > KeyBytes, count : 5
> > A7
> > 86
> > 02
> > 97
> > 9B
> > error rcv wait timeout
> > ID after 5baud init:
> > no data received
> > Error in Communication
> >
> > Please help me
> >
> >
> >
> >
> >
> >
> > __________ Information from ESET Smart Security, version of virus
> > signature database 4580 (20091106) __________
> >
> > The message was checked by ESET Smart Security.
> >
> > http://www.eset. <http://www.eset.com> com
> >
>
>
>
>
>
>
> __________ Information from ESET Smart Security, version of virus
> signature database 4582 (20091107) __________
>
> The message was checked by ESET Smart Security.
>
> http://www.eset.com
>