Ok, this is sorta a Jeff foxworthy thing. If your new helmet says "Tupperware, burp to seal" on the rim around the visor, it might be a bad omen. If your new...
Personally I think it is a good omen. The helmet - always was going to be dodgy due to bad workmanship - was bought by someone who had the sense to tighten it...
-maybe the belt is grabing a bit ? next time it fluctxes put it up and see if the rear tire spins a bit ? just a thought.. -- In TwistnGoScoot@yahoogroups.com,...
I was in the scoot shop a few hours ago and the mechanic was pulling down a Derbi Atlantis (100cc). It had a bit of a problem...the rollers in the drive...
... well, I am not impugning this particular brand of helmet. they might make very fine helmets; indeed, maybe this helmet was fine from the factory and...
... pulling down a Derbi Atlantis (100cc). It had a bit of a problem...the rollers in the drive thingy ('gears') had MELTED. Not the belt. I felt sorry for...
I,m still having trouble with my et4 in the rain. It dies in heavy rain and wont go again until it dries out. Is it possible to do anything with the electrical...
damn, ive heard nothing good about theses bikes.. get a kymco lol. I dont know what could be going wrong, is the engine getting water in it? ... From:...
Check the top of the coil for " carbon tracks", these will show as a dark line that comes out of the coil and goes toward a ground spot. This would conduct...
Mate, apart from the fact that you took it back to the dealer, contact HJC direct. They have a cool website. I once owned a Korean car and the dealer paid...
which hjc is it? i have th cl-14 and its holding up great ... From: Reigan Scott-Palframan To: TwistnGoScoot@yahoogroups.com Sent: Thursday, January 02, 2003...
My Gilera has similar speed and fuel requirements. I find it runs best of all on Shell Optimax (even higher octane rating than premium ULP). Some bikes don't...
Only after searching the archives and the internet for any information on making the Hyosung Sense go faster. I posted this request because of the lack of just...
... 120 ... has ... the ... the ... ................................................................... If they stay in the Derbi mode of high compression...
... a ... would ... ...................................................................... Really! The nerve of this guy ! lol Welcome to a great group of...
... I have the Derbi GP1, I would think that has the same motor as the Atlantis. Is the Atlantis still a faster sooter. Luke "boyracer" ...
Luke Owens
lukeowens@...
Jan 3, 2003 3:29 am
5142
My Derbi made a chirping sound, similar to a bird, almost. Turned out it was the front axle rubbing against the speedometer housing on the front wheel. Needed...
... of ... Atlantis. ... ................................................................... NO, the GP1 , being watercooled has a bit more power and is ...
Has anyone any experience of garaging a scooter in a metal shed. Due to shortage of space and a full garage I thought I would buy a shed to store the scoot...
That's a great idea. I've misted car engine sparkplug wires with water then start the engine in the dark to see if any sparks fly. ... a ... spot. ... the ......
I've heard a lot of condensation can form on the inside surfaces of a metal shed but small animals cannot gnaw through as they do the walls of my wooden shed. ...
Condensation is caused by warmer moist air coming into contact with a cooler surface. It is not what your shed is made of, but how it stabilizes the temperture...
If you want to buy a shed, metal is great. the walls can sweat, but that can be minimized either with insulation, or, better yet, a small vent grate, maybe...
just curious so you can cut into a meatl shed with tin snips very quiet wood would be much louder.. so will you lock the scooter up in side too or is it safer...
