mmmmmm, I never found the Old Marston group particularly helpful, which is why I have no wish to lay out a tenner to join again I had hoped that with this new...
I have been trying to find a primary chancase outer, and a luggage rack, for my 1929 model 2 s/v 350cc sunbeam, have tried ringing Paul Milner a couple of...
Yea, the sunbeam world runs on its own schedule and parts etc seem almost unobtainable... I feel your pain :( I can't help with the parts you need, maybe...
If yours is a saddle tank I could help with drawings dimensions etc, chaincases turn up a lot a jumbles but you need to carry a pattern with you as there are...
Does any body know what main & needle jet should be for a 1929 sunbeam 350cc sv model 2, the carb on it is a 75 type 5 with the two holes each side of the...
I have a 1929 350 model 8. When I bought the bike the carburation was rubbish and I contacted Surrey cycles http://www.amalcarburettors.co.uk/index.htm They...
-I have aready contacted Surry cycles, Hichcocks,and Amal/Burlen in Dorset, unfortunately none of them had infomation pre 1930. Sunbeam only made the model 1...
-sorry typo error 1929/30 not 39!! only two years for the model 1 & 2 350cc sadle tank. -- In The_Sunbeam_Motorcycle@yahoogroups.com, "velocmac350" ... it ... ...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the The_Sunbeam_Motorcycle group. File :...
The_Sunbeam_Motorcycl...
Nov 4, 2008 3:59 pm
409
On file now page from 1930 Amal carb booklet shows basic jets sizes for any engine I have the whole booklet on CD...
Hi folks, Just stumbled across the group and joined - so hello! Just wondering if anyone has any kind of literature / info / good illustrative photos which may...
I have been trying to cross refer the 1930 350 sv. main jet 80, needle position 3. is ok, but bore size 25A & model valve 4/5, I am not sure what this refers...
Not sure what 25 refers to, but surely all you need is to match the diameter of the inlet to the carb bore? I think its either 7/8 or 3/4 inch valve is the...
Hi All, Does any body know the opening/closing degrees for a Mod 9 camshafts and how much different are they to the Mod 90, as i am looking at getting my cams...
These came from a booklet I have with vintage motor settings. I cannot guarantee how accurate they are, but seem reasonable. 1928 seems to have been a...
Thank you Gordon. Interesting to see the Mod 9 and 90 have the same cams.I had assumed they would have had wider duration.Does any body on this message board...
I wouldn't assume the mod 9 and 90 have the same cams simply because they have the same valve opening and closing timing; the LIFT could be very different! ...
Just as an FYI I plan on bidding on the rear carrier and using it as a pattern to have some more made. I already have a chain guard (not the oil bath chain...
http://www.realmilitaryflix.com/public/261.cfm Some members of the group might be interested in this archive film of motrocycles. Any more anywhere? Don...
Had a email from my mate who is rebuilding my 1929 350cc sidevalve engine, saying He has removed the main bearings from the crank shaft they need to be...
Tell your mate to hang onto them.Even if worn, They are MC22; an obselete bearing but one which was used in a number of vintage bike engines, famously model H...
Yes MC22 bearings are used in veteran/early vintage Triumphs. They can be obtained from, www.veterantriumph.co.uk but be warned they are £42 each!!! I used a...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
