Hi Jerome, I have dealt with a problem that sounds exactly like what your describing. In both cases the pilot bearing in the end of the crankshaft was worn...
Is is feasible to remove/replace the tie rods and the steering rack bushings without removing the steering rack from the van? Any hints or warnings? TIA, Kevin...
Hey all, been lurking on this list for a while and bought a 2.5L subie for my syncro. Well, conversion parts are expensive and I have to have it running very...
volks, can someone please direct me to or pmail me a photo of an exploded view of a decoupler (like a drawing and not a side of the road "ohshit" sort of ...
82 Diesel vanagon for sale SLC UT. Runs (have to pull start it until battery is replaced). Has eberspacher diesel heater (have not tried firing up the ...
Are there any Syncros down here near Pismo Beach?? I think that I am going out on Wednesday near noon. Is anyone driving up to SDM on Thursday from Pismo...
Hello all syncronauts! This hesitation happens only when "lambda" sensor IS connected... I have checked: Spark Plugs: OK (new) Filters: OK (new) Idle control...
Hey Anthanasios, Have you checked to see if the heater in the O2 sensor is NOT shorting to the sensor? Use an ohm meter and make sure you have no connection...
FYI, I saw yesterday that Marvel Mystery Oil is once again on the shelves at Canadian Tire. Cheers, Frank Condelli Almonte, Ontario, Canada '87 Westy, '90...
So thanks for all of the help! A combination of all of your advice seemed to help. I bled it again by only using half strokes. The pedal remained really soft,...
Greetings all. We now have over 20 demands on De couplers . The feedback I am getting is that if we could produce them for around the $500 mark people will buy...
... 1pm: Pietra Santa http://www.pietrasantawinery.com/ A fairly good winery specializing in italian-style wines. Good, resonably-priced wines. 2pm: Calera ...
I have a 1987 Pass Syncro, It is a project van, bought without engine. Unknown history for what parts were not working. Now has a running 2000 2.5 Subaru in...
Enter your vote today! A new poll has been created for the Syncro group: Regardless of cost which engine would you choose? o 2.1 WBX o New 2.5 WBX o 1.9 TDI o...
Syncro@yahoogroups.com
May 3, 2006 1:20 am
28113
Explanation please. 1. New 2.5 WBX? Is there such an engine? 2. Poll list is different to what's on the e-mail. Les Harris ... From: <Syncro@yahoogroups.com>...
The problem with this poll, is no weighting of the answers. I love my 3.3 EG33 engine. I love the mileage Karl gets with the 1.9 TDI (which from my experience...
Ya know, I've read postings about the decoupler, but I really don't have a good understanding of what the decoupler does. Could someone please post a simple,...
3.3 SVX is the only way to go at my shop! dylan Syncro@yahoogroups.com wrote: Enter your vote today! A new poll has been created for the Syncro group: ...
Anthony, The prop shaft is considered to be a "solid" shaft in that it is driven permanently by the gearbox and thus always drives the front diff. This shaft...
Can anyone give my husband a ride from the SF/Marin/East Bay area to Syncro de Mayo? If so, could you drop me an email? coyote ... "I have a vision – maybe...
It looks like 3.3 you need more engine 3.3 choices for this poll, as the 3.3 "other" category is running 3.3 away with it... Thanks, Cory www.syncrowesty.com ...
Hello folks, Like the subject line says, please pmail me if you have any experience with this firm or their associated businesses. TIA, -- BenT [Non-text...
Subject line says it all. I want to pick up a 1987 ( ie: greater than 15 years old) parts syncro from the US tomorrow. Can this be done? What documentation do...
Have a look at the SyncroSA group. Gordon Craig has got decouplers, I just didn't pay attention to the price but with the exchange rate it should work out very...
Hello All, I'm just rambling... When I worked for VW back when these vans were new, it wasn't too long after they were on the road and some customers were...
I'm stillleaning towards an I5 turbo.. but there is "NO REPLACEMENT FOR DISPLACEMENT" and if $$ were no object i'd likely go 3.3 subis 6 or the new subie FLAT...
