Hey marbles, You should try mounting them on a bajaj. The rear fender bracket needs to be stretched 2 more inches to clear the wider cowls. The floorboard...
Well. I'll get in trouble for this, I'm sure, but that is just one of the "differences" that makes a Stella "more of a traditional scooter" than a Bajaj. How...
I don't need to kill you. The guards weren't put on to make the bike more "vespa-like"....I needed a place to mount passenger pegs that my 6 year old daughter...
Anybody have any experience mounting the old-style tractor seats on a stella? I mean the two separate seats, one for the passenger, one for the driver? I...
Hi, I just took off my cowls to check everything out for the warmer weather. Charge Batt, etc. I noticed on the engine side a black ground wire hanging loose. ...
... ground from stator or igintion unit, not sure, since im a vespa person, and the stella ignition, while it runs the same, is a slightly different setup. get...
Greetings All Since we have been selling Stellas we have had several customers that have wanted to "retro" the Stella. This gives the Stella the classic ...
I was at a rally yesterday and saw a green Stella that was about a year old. There was a large amount of rust on the chrome around the speedometer. When I...
... one ... I too have been intrested in this seat style/config. Is it more comfortable than the stock bench seat? Does it push you farther forward than with...
... i had this setup on my P200 for a few years. A) im 6'1 B) it looks REALLY cool C) you do sit pretty forward, i got into a habit of sitting between the ...
Occasionally, when I come to a full stop with the clutch in and the bike in second gear, I can't get it back down to first. I have to rock the bike a bit to...
Hi, Just installed my Sito + and a #98 main jet. I am assuming the main jet assembly is just screwed in until tight? There is no adjustment to this correct? ...
Its not a problem, it is how the drive train is engineered. The four gears are in a stack. The middle of each gear has a cross- shaped cut-out. When you...
well, Someone once told me you can't shift unless the bike is moving. Make sure you are at least getting to neutral when you are stopping. This also happens on...
I made mine stop 'chirping' almost a year ago so i am not sure which wire to pull, but look at your wireing diagram to figure it out. Remove the two screws...
Thats normal. Its easiest to downshift as you are slowing down. Rocking it a bit forward and back works just fine. Its the same with a standard shift car that...
Hello Stella-philies Here in northern michigan the weather cleared and warmed to a point to ride today (45F ... ohhh warm) after buying Stella in November, she...
... which wire to pull, but look at your wireing diagram to figure it out. Remove the two screws inside the glove box to losen the bottom of the horncast....
... Josh, That's right. The main jet assembly just screws in until snug, not too tight now. The adjustment is accomplished by the changing the jet. Once a...
... <jagsue2003@y...> ... tight? ... 7mm ... the ... snug, ... the ... rear ... run a ... because ... variance ... Thanks, I didn't realize I had to mess with...
... bike in second gear, I ... get it to go into gear. Anyone ... I also had this problem and used some of the suggestions in this thread to deal with it. I...
THanks for all the info folks! Sound like I don't need to worry that it's a problem with my bike! I'll just downshift all the way to first from now on. Tad...
Hey all, just wonderin' what kind of spark plugs you've been using and happy with. Anyone notice any difference between using a resistor type verses a non...
Hi! What carb are you putting this #98 jet on? We have the Sito plus and Del'Orto 24/24 with the Polini 177 kit. Do you know what jet would be stock on this...
... Yeah, the Sito sounds great, runs great too. For the investment it can't be beat. The low speed adjustment may not need to be messed with. If the scooter...
