Dom--just go on ebay and buy SL125 front and rear wheel assemblies from a salvage yard---they should bolt right up, then you can check for clearance. Back in...
I have a '71 CL 70. If the battery is charged, the lights work when the ignition is on, even if the engine is not running. It seems, however, that the...
Hey, thank you all! I have been riding it up and down the street the past few days. The float was hung up b/c the bowl seal was not in it's place. You guys are...
... I've fixed the inductive drive before, but not the spring. The speedo is not really intended to come apart, or more to the point - it's virtually...
Jim As for speedo repairs you can pretty much hang it up when it comes to the Clockworks spring included.As I like to call it. When springs are giving you...
... I recently acquired a '60's CT90 and a CT200. Both are basket cases, but I'm committed to making them go. I have attempted to subscribe to the above list,...
Thanks,I did just that it was all correct. ... KennyM ... would not turn over the piston.We found the clutch assembly apart and repaired it from parts from...
Have a 1980 Ct110 that the choke has to be in the full up posistion (choked) to run outher than idle.I have cleaned carb twice and blew out passages and...
Hi, You should check the float. make sure it set properly and supply the correct amount of gas inside the carb bowl. Less gas on the bowl mean too dry setting....
Just a little feedback so this thread is marked SOLVED. Finally had time to devote to analyzing my problem. Found 3 causes: 1. Inside the throttle grip, the...
The previous owners of my bike apparently managed to bend BOTH foot pegs up so high it is uncomfortable to ride. I don't have facilities to heat and straighten...
Just hit it hard with a rubber mallet, but make sure its bolted down tight. I swear it works! let me know how it comes out. rtim12006 <rtim12006@...>...
Hi Paul- My CT110 ran the same way until I got the emulsion tube out of the carb, carefully cleaned the horizontal holes with some soft wire (they were...
Take the footpegs off, dont try to bend them on the bike as they are only held on by bolts in alluminium casings.... Once off put them in a vice and use high...
I'd love to do that, as I suspect that's the best way, but... I live in a condo complex, have no work bench, no vice, and cannot even remove the seat on my...
Thanks for the suggestion, but when I first got the bike, I tried that both on and off the bike and even with a 3 lb sledge. That booger won't bend, partly ...
soak the rubber in boiling water or use heat to sofen them and they should pull off with alot of effort. On cg125 footpegs with sidestand, the rubbers are held...
I go to one of several local machine shops to get such things straightened. They have usually a variety of presses and have experience in shaping metal of all...
Hi, I would still say better to heat it up and straighten. Hammer it may cause the bolt housing on the engine damaged. Based on my experience. Anis Setyadi ......
I tried the sodering thin over the long weekend. It held for 1 trip up the street not on the way back. So now I am looking for a speedometer although it's not...
Jim What model&year honda was it? KennyM Jim Nolan <jimmer_48@...> wrote: I tried the sodering thin over the long weekend. It held for 1 trip up the...
Hi folks. Hope all is well. I just wanted to let everyone know that a new club for all small engine biking afficionados is forming in the Northwest Atlanta,...
I think I may have one ... pretty sure since I've got a few frames and such that I picked up. Actually one has some pretty good other parts...year with the...
While refurb’g our QA50 (‘75) I ran into what is probably a common problem…demounting the tires from the 2-pc wheels. I’d imagine when things are new...
Charlie, Ebay purchase and be patient I have sometimes looked for months for certain parts and sometimes they do come up and I also have a cap on how much I...
Someone else suggested patiently watching Ebay and that is very good advice. Also, there is a good parts supplier for everything else that you should be...
Tks for the input...I'm well versed in the miracle (?) that is ebay. When talking with people about VMX (that's vintage motocross, btw) the question always...
