... Earth = Ground. ... Yup. The "Park" setting is for leaving the bike in the street, against the curb or in a parking space at night. The engine is shut off,...
Mike Gladu
mgladu@...
Jul 1, 2002 8:18 pm
302
... Also make sure you have oriented the slide properly when you reinstall it. If it isn't lined up properly, the slide will not drop down into the throat and...
Mike Gladu
mgladu@...
Jul 1, 2002 8:24 pm
303
... You can get a new one, but first try to put the old one back on properly. If the metal pin inside the cap has "threads" on it and not just concentric...
Mike Gladu
mgladu@...
Jul 1, 2002 8:30 pm
304
Yup. The "Park" setting is for leaving the bike in the street, against the curb or in a parking space at night. The engine is shut off, but the taillight is...
Could someone please advise me on how to remove my email address from this mailing list as I will be changing my address shortly. Thanks in advance ... From:...
Karl DeSouza
karl.desouza@...
Jul 2, 2002 6:59 am
306
Going..... Going..... well.... by the time you read this I will have knocked you off the list manually. Anyone can join, leave, rejoin etc by going to the ...
I've got a 69(I think) CL50, it's got a 4 speed manual transmission. From 1st to 2nd is very harsh,you have to give it a firm push to get it to go into 2nd,...
Things have been a bit busy over te past few days, but this morning I worked out a test procedure for testing your 3 or 4 wire rectifier. Note that rectifiers...
The most likely thing that I can think of is that the operating pins on the end of the selector drum are worn or bent. The gearchange should be fairly smooth,...
Hi guys, I have a 1984 ct110 engine which has had the left side crushed by a curb stone. The left half of the crank case , the left side cover and the HI-Lo...
You need crankcases for any non-electric start, CD ignition bike, but preferably one with the same kind of clutch as the CT as sometimes swopping the right...
http://freepages.autos.rootsweb.com/~antrev/hondac.htm ... __________________________________________________ Do You Yahoo!? Sign up for SBC Yahoo! Dial -...
pman
pearce_w@...
Jul 6, 2002 7:13 pm
314
hello all!! anyone know where i can get nos parts for my baby? i need a seat & a kick starter lever. thanks...
Can anyone help. I have re-built the engine set valves and timing and initial carb settings, but am unable to stop it running rich and rough. Before the...
... Have you rebuilt the carb? Have you checked the float to make sure it isn't leaking (shake it, there should not be any sloshy noises from it). The float ...
Hi, I put a either 70cc or 90cc carb on my CL50. The flange on it is not on an angle like the 50cc one is, so it puts the carb on a angle. When you give it...
Ania: I sent you an email last week with an excel spread sheet of carb info. Did you get it? Robert P. Reil Managing Director, Motorcyclecarbs.com, Inc. 745...
Hello, I'm Keith and I'm in Nottingham, UK. I know it's not good form to join a group and then start posting for advice; but here I go anyway... So the bike's...
No I didnt get the info, can you send it again. On the same subject, when I rebuilt the engine I set the timing up to the marks on the flywheel. With the...
Robert, Sorry about the delay, there was a lot of work stuff that I had to get through before going on holiday. It is an excellent list and I intend comparing...
Keith, don't worry about posting for advice straight away, its what most people do! The easiest answer to the problem is to try and find another head at a...
... The question is, how much of an angle is it? Carbs operate at a range of angles, but if it is not at the design angle at rest then you are going to run out...
Ok no problem. I was just wondering if you got it and I assumed you would have replied saying something like "AWESOME!!!!" Robert P. Reil Managing Director, ...
Personally I think it would work as long as the angle is not more than say 20degrees. As to the way it is running I would start looking at jetting and modify...
Hi again guys. I was looking at some of the spare parts that I have and I found a lower end of an engine that has no type or serial number stamped on the...
... Do you mean it has a transfer box - an auxiliary 2 speed Hi - Lo gearbox attachment on the left hand side? ... Do you mean the complete side cover, or...
