Hi Ian, the dealer in Yorkton, Sask is Schrader Honda and their # is 306-783-9256. The parts mgr is Lyle and he is usually a very accomidating fellow. If he...
Bryan, Many thanks!! I will see if Lyle will sell over the phone and send them to me. You have been helpful "above and beyond the call of duty". Thanks again!...
Someone posted some parts TIFFs. Please contact me off list. If you give me the whole lot, I'll convert them to a PDF or HTML depending on what seems more...
Hi all, this new guy needs your help. Just got my trainer bike back from son-in law and are ready to clean it up for the little ones coming up. I can't get the...
hi,im trying to put a 1973 xr75 back togather.im stuck on the carb.anyone know the correct #S ? any help,any info at all would be great. thanks,ken....
I have many parts for the Honda Sport 50 (C110) e.g: Fuel line, Handle switch, clutch cable, piston, Handle bar (ALL NOS) I also have 17" white wall tire and...
I would be interested in the CT 110 handlebars, how much? Thanks, Ride On.....:)TF ... From: edarius73 To: Small-Honda-Singles@yahoogroups.com Sent:...
New member here...I just reclaimed my brother's 1965 and my own 1966 C110's that we were riding in the early '70's from a fellow who's had them in his mom's...
Hi all, glad to be part of your group. I currently have a 1984 Honda CT 110 that is an almost daily rider. I bought it three months ago; It ran, but would...
I saw some pictures on another website of what appears to be a 50cc version of the 250 Rebel. Does anyone here have any information (size, horsepower,...
... Those are Honda "Little American" replicas from 1997-on. Genuine Honda Japanese 49cc motors in the Magna, Jazz (Shadow/Rebel) and Benley copies. The Jazz...
Look at this site, http://www.worldwidedistributing.com/index.htm Also do a search for the knight 50. Honda has a bike called the Magna 50 but it is not...
... (no ... OK, looks like the cost factor will rule that one out. :( The Chinese model...are the frame and wheels of decent quality? I know that the Chinese...
... QUALITY OF LIFE issue.(LOL!) ... It wouldn't cost all that much. There are tons of the 50-70cc engines lying around in scrapyards. One scrapyard nearby...
At that rate J-D, I'm forced to agree w/ you. Although... I've had little luck in finding too many descent m/c parts in the junk yards nearby here in PA. Ride...
... It shouldn't cost much to rebuild one of those. The lower end was almost bulletproof. I would just go for a top end rebuild unless there is another...
... little luck in finding too many descent m/c parts in the junk yards nearby here in PA. ... What part of PA are you in? If you are close enough to Ohio,...
... The rep for the Chinese engines differs depending on who you talk to. They come off subsidiary lines in China, Thailand or VietNam ready to install in...
I can only comment on my personal experience with a Huwai engine. I picked it up on Ebay for about $251.00 US. I bid on this particular engine based solely...
I forgot to mention that I also had to replace the gear stop spur to allow for 3 speeds. Jimmy ... From: ZB To: Small-Honda-Singles@yahoogroups.com Sent:...
http://www.theoctop.us/images/forsale/c100/clutch_plates.jpg They say "1102202" on them but have "1002202" crossed out. They have 30 'cogs' on the inside...
Thanks for all the input.Looks like I'll have to tell my nephew to start checking Ebay and see what he turns up. Then from there it depends upon how it runs...
Greetings, just a short note of introduction. I have just found a S65, it has no paper work and I am not sure of the year (mid 60's?). Although it does run,...
... S65, it has no paper work and I am not sure of the year (mid 60's?). Although it does run, it does need a bit of work. ... I expect for performance? Also...
try increasing the source coil current for better fuel burn, also try fuel with better octane or fuel mixture... also jetting... ... Yahoo! Messenger -...
