The following Small-Honda-Singles poll is now closed. Here are the final results: POLL QUESTION: How did you find your way to this group? CHOICES AND RESULTS ...
Small-Honda-Singles@y...
May 2, 2002 1:24 am
167
Hi, I have recently bought my first classic bike - 1976 XL125. Unfortunately after closer inspection a previous owner has decided to change the carb for a...
Karl DeSouza
karl.desouza@...
May 2, 2002 2:15 pm
168
Hi Karl You may want to check out this site, you can put want or for sale ads for free. I've found alot of what I needed for my SL100 K2. Mike 1972 SL100 K2 ...
Please take my e-mail address off the daily chat group list, I need to drop the daily messages at this time but would be happy to remain in the group . ...
Hello all I have a CB125s 1972, that I have restored over the last 10 years or so, she is a lovley little bike but for one annoying problem that I have not...
... From: David Clay To: Small-Honda-Singles@yahoogroups.com Sent: Saturday, May 04, 2002 1:50 PM Subject: [Small-Honda-Singles] CB125S running problem Hello...
An afterthought: Coil or condenser, or even something as silly as a HT cap. Bill ... From: David Clay To: Small-Honda-Singles@yahoogroups.com Sent: Saturday,...
Ah... with all those repairs you must be an expert on them by now - ho ho! Yes, there are lots of gaps in the specs, the site has only been running for some...
Hi, I can't find you among the members, so I assume you have taken yourself of the list. I was unable to get back to you earlier as my computer trashed its ...
Jon, There is no simple engine swop that will give you everything that you need. If you can find yourself a cylinder head from a 1970's C70 or CT70 then this ...
I had an MR50 that did something similar only under load. It turns out that a wire under the flywheel was bare. With no load, the current would go where it...
Hi Dave, The problem with these kinds of things is that it is knowing where to start. The best way is to start with the first point in a system and follow it...
I have had my cylinder reboared, and the replacement piston supplied is different from the old one. The old piston was concave by 2mm and the replacement is...
We just purchased a used '75 ct90. It ran great for a few days. Changed the oil, gas, spark plug, and air pressure. After running it for about an hour, parked...
someone will give you more details but don't panic. Oil in the alternator casing is correct. I used to have one of similar vintage and the oil frightened me...
Put both pistons side by side and check first if the distance from the gudgeon pin centre to the top corner is the same on both pistons. It sounds like one of...
Hmm.. oil in the generator housing... The first thing to do is to remove the flywheel, and for this you will need a flywheel puller of the type that screws...
My real apologies to all....must get my brain in gear. I stated earlier my 90 had oil in generator. It actually had oil in the clutch housing, not the...
Glad this isn't a newsgroup.... Could you imagine the flaming! Bill ... From: Ania Butcher To: Small-Honda-Singles@yahoogroups.com Sent: Thursday, May 09, 2002...
I have a Honda CT110 AKA Postie Bike. Postal workers use these small machines to deliver mail down here. When I bought it last week it had a small amber bulb...
Ken, I don't have a CT110 wiring diagram to check, so I am not sure what kit your bike comes with. The generator can't be adjusted directly, the generator on ...
can anyone tell me how to set the float level on a XR75 (early 70's) __________________________________________________ Do You Yahoo!? LAUNCH - Your Yahoo!...
Do you mean I need to pull the rotor alternator assembly out and replace some seals behind it? Do I need be aware of any timing issues? Are these seals easy...
Yes, you have understood correctly. There is no problem with the timing, although it is no bad thing to check the condition of the points while you are at it,...
Great, I'll try tackling the rotor alternator casing. Wish me luck! Thanks, -ct ... ADVERTISEMENT [Image] ... [Non-text portions of this message have been...
