Pete: checked my stuff, I don't have any 52-3 lenses....I occasionally see them on ebay, or you can try charles thomas or herb scheffer...herb should...
what are you guys going with for plugs and wires. rockauto sells a non resistor autolite #216 for $1.13 a piece. no radio so no resistor needed here. they also...
Beware of Rock Auto plug wires. They do not fit. I purchased both sets they list and on the Lincoln 317-368 engine, two of the wires are not long enough. I...
NAPA has wires. ... From: Tom<mailto:Mercfreak@...> To: RoadRaceLincolns@yahoogroups.com<mailto:RoadRaceLincolns@yahoogroups.com> Sent: Tuesday, June 03,...
bill culver
bigeasy3@...
Jun 4, 2008 12:13 pm
1250
are you guys doing the plugs through the wheel well or from the top? I noticed when doing the control arms I had a good view of the plugs. Pulled plug...
Pete i had a problem with using Carbin plug wires on a 54 linc while it was 6 volt , it cut out at about 3500 rpm , i just talked to a guy with a 54 ford he...
MartinRP2@...
Jun 8, 2008 2:51 am
1252
not sure what a carbin or real wire is, i got the napa set, looks like its made by beldin. ... From: MartinRP2@... <MartinRP2@...> Subject: Re:...
I've always done them from the top. ... From: Peter Salzano<mailto:tekdope@...> To:...
bill culver
bigeasy3@...
Jun 8, 2008 4:10 am
1254
Pete: if your napa set came without the wire caps inistalled already, just look at the end of the wire....if you can see real wire in the center of the rubber...
bill culver
bigeasy3@...
Jun 8, 2008 4:15 am
1255
Pete the carbon wire has carbon in the center , wire wire has real wire in the center, carbon wire is somtimes called radio suppression wire, Rick<BR><BR><BR> ...
MartinRP2@...
Jun 8, 2008 1:15 pm
1256
Does anyone know what this tool is called and where can I find one?...
is everyone elses wire being held in by this behind the block? http://redcatmedia.com/pete/av/May08122s.jpg i unbolted it from the bottom but...
Originally yes, from the factory. it's usually just one bolt that holds it to the block. you'll have to pull them up as a group, just be sure you mark what...
bill culver
bigeasy3@...
Jun 8, 2008 7:49 pm
1259
check with john grove, charles thomas or walt blankenship. if you need their telephone, email me. bill ... From: Fred...
bill culver
bigeasy3@...
Jun 8, 2008 7:50 pm
1260
I figure as long as I mark plug #1 on the distributor I can work my way around from there. ... From: bill culver <bigeasy3@...> Subject: Re:...
Technically, you're correct I always managed to mess up at least once, tho. ... From: Peter Salzano<mailto:tekdope@...> To:...
bill culver
bigeasy3@...
Jun 8, 2008 11:54 pm
1262
I have never seen one like it , it must be to pop ball joints out of the Tapper fit, i use Forks to pop Ball Joints. Rick...
MartinRP2@...
Jun 9, 2008 2:11 am
1263
here's one from my 87 chrysler shop manual. I have access to the dealer parts search engine, if you want I can get you the list of dealers that stock it. Maybe...
Arthur: this isn't an email list...it's a yahoo group....don't know how you got on it, and don't really know how to get you off of it....you might email Mike...
bill culver
bigeasy3@...
Jun 10, 2008 12:36 am
1266
go to www.yahoo.com click on groups on the left sign in click RoadRaceLincolns top middle, click Edit Membership scroll to...
Thanks, Pete. ... From: Peter Salzano<mailto:tekdope@...> To: RoadRaceLincolns@yahoogroups.com<mailto:RoadRaceLincolns@yahoogroups.com> Sent: Monday,...
I took him off ... From: Arthur Margain To: RoadRaceLincolns@yahoogroups.com Sent: Monday, June 09, 2008 1:33 PM Subject: Re: [RoadRaceLincolns] Re:...
The only way he could join was request it or sign up himself...I will check my old computer to see how he joined. hope everything is well with everyone Mike ...
can anyone help? I have one I just need to find it on the old computer. I think I have moved over only half of my stuff. mike ... From: Mike Boyce To:...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
