Hi All, First, I am in no way involved in the sale of nor will I profit from the sale of this RV. I am quite happy with my 84 Duke. I saw it a while ago and...
Sorry I forgot to tell you which folder the pictures of the Revcon for sale are in. *Revcon for sale in Cincinnati*. Bet you would have never found it. Joe...
Or maybe install a pump like this http://store.summitracing.com/partdetail.asp?autofilter=1&part=TIL-40-524&N=115&autoview=sku Some of the off roaders and four...
Gordon, The machine shop line bored it, like you would do a engine that had spun a main bearing. Finding a hsg. probably wouldn't be a problem if all or most...
Curt, I don't think temp. is the problem. I am hard pressed to get the oil temp above 150 degree F. Now if you "Y" the return line so it dumped the return...
Great research. If I rebuild my diff, I'll give serious thought to additional cooling and oiling. How can an electric pump be engine speed proportional? Is the...
I can only compare to my current set up. The original over all ratio is 3.36. My over all ratio is 3.94. 4.10 gears will give your an over all ratio of 3.69. ...
Marcus, I think, "motor" speed is the pump motor not sure if it can be varied by voltage but that is what I kind of thought may be wrong. Later Curt...
Lyle, That was what I was thinking, I thought it was the outer bearings however. The temp thing was just to keep the pump from running full time, it is rated...
Lyle wrote: " Curt, I don't think temp. is the problem. I am hard pressed to get the oil temp above 150 degree F. Now if you "Y" the return line so it...
Hi. I've rebuilt two dana 70's on differnt trucks and unlike some dif's there wasn't a crush washer on either of them. The pinion is mounted on two opposing...
I finished putting the rear gas tank on this afternoon after replacing all gas lines, selector valve, wiring and switch. It takes 75' of steel fuel line for a...
Malcom: I've never had a diff in my hands and couldn't point to the pinion given 3 chances! Do you see any downsides to it running backwards - other than it...
Marcus/Malcolm In most differentials (at least the old ones -until 70s anyway) the crush washer was what controlled how far the drive pinion went into the ring...
Marcus, The return lines on my 82 screw in near top on the front of the back(63)tank and on the rear of the front(37) tank, and yes they are double flared. All...
As far as noise, mine made a low whine in the no load condition such as starting over a slight grade, about the same place where you would hear a rod knock if...
Lyle, What line did you use? is it continious or sectioned, all I can find around here is the brake line type that comes in joints up to six foot lengths. I...
Curt, I'm not a big fan of the "NEW" auto stores, I prefer the old ones with the machine shop in the rear, but in this case I was only able the find 25' rolls...
Yes that is what I be looking for hadn't looked to hard on line yet just looking around here the leak just did start got hot and a Very fine spray leak...
Lyle, Know what you mean, unfortunatly ours burned a couple of years back and the old boys were close enough to calling it quits that they sold out. We have no...
Here is one for you. [url=http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=270036854729&fromMakeTrack=true]Ebay 270036854729[/url] It says '66...
great link, thank you ... __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around ...
... Funny how that works! According to insurance companies, the most obvious way to tell the fire was arson is when they take all their personal stuff out of...
Marcus, Ours was an electrical short in the machine shop side, the old building had wooden floors in the storeage area and when the paint started it shore was...
... Hey Dave, that's a pretty interesting rig. I don't know if it's FWD or not. It looks like a trailer conversion. Check out that front-seat side visibility...
Lyle: So far as crush washer pre loading the Pinion, you are correct and I was wrong. Been a long time since I worked on differentials (and I worked only a...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
