Thanks, but I doubt they are the same, not sure about the Olds, but the Chevy is not the same. Mine are made like Chryslers in the 70s/80s except larger. Ford...
If they can't tell you specifically what is different, then they are not qualified to judge which is better. Just simply making a claim without backing it with...
Lyle; The Toro GMC are 1/2" X 20. I ran the die over my bolts and that tap through my toggles when I had them out last month. The 3/4 T looks like 9/16", but...
Oh, they can tell you what's different. They can bury you in data and different opinions- well informed opinions. I've gained a great respect for the GMC...
Dave; I think of an RV as a truck, not a unique vehicle. What is so different in an RV carb from a truck carb? When you look at the vehicle in this light,...
As Gorden is saying, I am always suspicious of "exclusive" anything. While it is well known that greater load requires a richer mixture, the practical reality...
OK, here is the dim. for a SN anchor 2-11/32" X 1-1/4" X 3/4" . There are 4 small reliefs cut where it rides in the 1-1/2" frame hole. I wouldn't mind...
Thanks Dave. Despite my age, (just south of 50) I never messed with carbs. I was forced to get pretty intimate with Chevy TBI though. So will the carb on the...
Dave; You have nailed it exactly. The power valve spring needs to be stronger in a truck. I think it is a "purple" spring in the GMC. The jets and the taper...
Hi all, is there an easy way of changing cv boots.Mine have each small crack slinging grease out.Been searching old posts and no luck, maybe not using right...
Rene, if you are talking about a 250, there is no easy way. Using a split boot kit will let you do it without removing the axle, otherwise you will need to...
Hi William, no its not a 250 mine is an 87/31 Prince, but it shouldn't be much different than your 250 in that regard at least I'm hoping that it can be done...
I think you can remove it without pulling the ball joint, but you do need to pull the tie rod end. This allows you to turn the wheel farther, so you can push...
Thanks Dave, I kinda figured that but trying to avoid it. Any suggestions on breaking ball joint loose without damaging ball joint rubber? Also how much time...
Hello all. We are changing our front 16.5" steel rims to 16". Stockton Wheel takes our center and welds a new rim on for 175.00 each. I know some of you...
depends on your purpose. If you want a tire to do well in the snow or in a dirt campground, you can't beat Bridgestone Dueler A/T Revo. This is the primary...
20 lbs sledge and a 2 lbs sledge. Wedge a load to spread the ball joint. Then place the 20 lbs sledge on one side of the spindle mount and wack the other side...
Thanks Dave, when I picked this coach up I was told by P.O. that he had spent a ton of money at Marty Moore's everything in the front I mean everything is...
Lyle; I haven't forgotten. I took a quick look today while I was in the middle of changing a starter, but did not see the toggles. I'm waiting for parts so...
I needed to change a head light (1982SN) and found an ear off one rim and 2 off the other. I can't find them with the correct screw hole spacing. Even the...
Somehow I've been very lucky in that regard. While I've had my share of troubles on the road, I've never been stranded. There's always been a solution...
Lyle I have had similar problems with my old(66)T-Bird what I did was to cut some tabs out of light gauge aluminum drill required holes bent them where needed...
Lyle; The GMC/TORO toggles a rough cast and are 2 5/16" X 1 1/4" X 5/8" The 4 reliefs are 7/16" wide and 1 9/16" Center to Center. The bolts are 1/2-20 UNF...
Can someone tell me what the purpose the solenoid on the alternator mount is for and what activates? Four wires, 2 battery cable size and 2 12ga. Some of this...
Does anyone have an idea what I should torque the front wheel bearings to? I ran across in my manual somewhere that its 150# same as wheel nuts.But I don't...
The biggest problem is with the Export from the US, not the import into Canada. You have to fill out the export form then wait while they check that you are...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
