... I knew ... though... ... You can get a welder from home depot for under three hundred dollars and tubing can be really cheap depending on the gauge. I buy...
Hi Jeff, I don't know About any of the other guy's but I saved some of the hand rails for scrap steel in case I need to make something. The other thing I kept...
Hi Gadget, About the fuel guage sender, did you have to cut the tank or is there an axisting plate to install the sender? Can you recall or do you have the...
Geoff, this sounds like what I might want to do, when you get a chance could you show this in detail on your website or post the pictures for all to see. ...
I already have a few pictures of the new wheel well and channel iron posted, I'll put up some of the seat mounted and driver's surround. --Geoff '82 RTS CA...
Still looking for the part number for a 9E90 injector.... But I ran across this... http://www.mde.state.md.us/arma/Programs/Mobile/Diesel/Summary%20of% ...
Hello all, I have seen a few RTS buses with the exhaust routed up near the roof and out. Does anyone have any pictures of the engine compartment that show this...
A few people have re-routed their exhaust out the rear cap, but since I haven't done mine (I need to) I can't help you on routing. As far as engine noise...
OK I had to "rebuild" my power supply fan because it's a BIG fan for a 300w power supply. It's an old Everex full tower case that I recycled, it's so old that...
The high exhaust system is a very convoluted route(i've only seen line drawings in a parts manual)..... if you ever see one you'll know what I mean. I'd like...
What is the main reason for routing the exhaust out the cap? Is it to keep most of the Gunk from the exhaust off of the toad, or is it somehow quieter, or ...
Dave
davez_rts@...
Apr 2, 2002 11:04 pm
1628
The redirection was originally done by the manufacturer to get the exhaust off of the ground level so it won't impact the sidewalk foot traffic as much as well...
If you all look at Dwight's pictures, you will see he did redirect the exhaust out the top back. I guess Dwight is 'sandbagging.' I think he has done an...
I am assembling the pieces for routing the exhaust topside. My local "Fleet Pride" has all the sizes of pipe (bent and straight) clamps, and various sizes of...
I think, for me it would be for keeping the exhaust off my towed car. You will have to used your bus for the first 3,000 mile trip, to know what I am talking...
WULF WARD
wayward@...
Apr 3, 2002 5:26 pm
1633
There is one problem I have with routing the exhaust out the rear cap and that is the electrical relay box on the left side of the cap. Those of you with older...
Hey you guys, haven't been keeping up with all the post, been sifting through them the past couple of days, alot of post there. The exhaust routing through the...
Steve How's the race cars??? haven't seen you around in a long time..... You can check out my burning blanket photos in "Joe's RTS". Did ya have fun like me...
Geoff I finally got off of work during the daylight hours and went out to the storage facility to check out the little sliding windows for the driver's side......
Before I get to committed to anything here, does anyone know the rated working load of the stock wheelchair lift in an RTS II ? I'll have to dig out the book,...
Would it be possible just connect to the existing pipe at the bottom, & maybe with a couple of turns run the pipe up the outside like the big chrome pipes on...
As I recall the rear RTS wheelchair lift is rated at 300 lbs. I'm not sure if you know this, but the bus driver has to operate the lift at the rear controls...
My manual came recently, & I was reading that about operating it. Seemed like the driver needed orangutan arms! I can't understand why they would set it up...
Just a thought........ on the 6v92 with the round muffler/ceramic catalist, couldn't one just rotate the exhaust end cap (loosen clamps and twist) thereby...
