I used 1/8" steel, no frame, no baffles, no acid, just poured a quart of epoxy in it, rolled the tank around, poured a second quart of epoxy and rolled the...
Go to the files section, there is a pros and cons some where in there. also you may check in Dwight's Breifcase for them. The address is in the Database...
I think it is the first gear that was removed to make place for the bevel gears and it is those gears that are not able to take the high h.p. With that said,...
Hi Jim Sorry I have been unable to read my mail, I just need the standard RTS regulator. thanks for remembering Don Hall 82 RTSll Amarillo,Texas ... ...
Hi Dwight, Painting inside of steel tanks. That's what I do for a living. To make a liner, including epoxy bond, the surface has to be SP-5 clean. That's a ...
WULF WARD
wayward@...
Aug 2, 2004 12:21 am
11588
Hi All Here's plans for a DIY 30 amp "3 way transfer switch" Shore / generator / inverter http://www.gmcmhphotos.com/gallery/showpic.php? ...
Why not just add a second rad. right in front of the the present one, I think there is enough place for it ?? Dwight On Sat, 31 Jul 2004 08:57:43 -0700 (PDT)...
Been 3 years and I have not opened the inspection hole to see what is going on in there ?? Guess I need to some day ?? Dwight On Sun, 01 Aug 2004 18:52:42...
I am going over there on Tue, I will ask how much it costs to up your DDEC II to 375 hp. And on the subject of burnouts... Once upon a time I worked at a fleet...
... From: "Jim Ramos" <jimramosusa@...> We also had some 4106's and one day I followed a driver up the mountain in the shop pickup, because we were doing...
I have a 1978 RTS II that has had some water damage in the rear electrical compartment. Does anyone know where I can get an inexpensive copy of the wiring...
I had the book you are requesting but gave it away to one of the members that owns that series of a bus. If you have the VIN and Model Number and where it was...
Gadget has that one, the '78. (80201) I don't recall the electrical stuff being all that different from the '82. (80204) You might just be better off buying...
Does anyone know the easiest way to get the compressor out? I have the four bolts holding it to the bracket off, but there is no clearance to get it out. Do I...
Is it OK to run the ONAN genset mounted in the old AC EVAP bay while driving? The scroll fan vents down into the engine area above the big Air intake tube and...
I just did this. I pushed inward on the top, and put a piece of wood under the front lip. Then I pulled outward and as it tipped outward, with it pivoting on...
After I removed all the bolts and nuts. I lifted it straight up and over the side fender by myself. It only weighs 120 pounds..... Well, that is what Old ...
We would like to remind you of this upcoming event. New Members: Please Read Date: Wednesday, August 4, 2004 Time: 8:00AM EDT (GMT-04:00) If you are a new...
RTS-bus-nuts@yahoogro...
Aug 4, 2004 11:47 am
11603
I think that different transit companies may use different filters and adaptors, or at least that there are differing filters that are used. I have the...
Thanks for the help (Chriss & Joy also) I had to pull the center (2)heads off to get mine out, but it is done. Also thanks Donn for the help with the Interlock...
My email has numbers that should be added to your faq then. The primary fuel filter numbers are different. I also gave Luber Finer #s which are still made, and...
I have an '86 MUI 6v92ta... I think I need a set of 9G90 Injectors for my hp upgrade... Does anyone know a good source that can get them to me fast and cheap? ...
What about these Injectors.....9285's There are 8 on ebay... Injector Tag No: 9285 Engine Series: 92 Part No. 5229400 Timing Injector: 1.460 MIN/MAX: 80-86...
....Hi Busnut2004; AL Schultz up here. Welcome; I don't know much about busses but I've been invovled with safety for about 25 years at the foundry where I...
