FEAR NOT!! If you looked at the sides as the RTS was crushed by the ship, the panels did not crush right, they folded then crushed like thin metal. Being...
Pete I mounted them in the escape hatch in the rear and I think I cut a hole for it in the front. I used heavy plywood and wood to support the mount. I found...
^_^ i know it was computer animated but it was still disappointing to see a RTS "destroyed" ... i liked the yuppie scene where the guy's all like "its fun...
HI Geoff Your wrote ---> "...(BTW, just what do people call these oval design, two section walls and ceilings we have???" I believe it's called ---> monocoupe...
From the Millennium website: "The RTS is available in the standard high floor configuration and utilizes a welded, modular stainless steel body construction....
... design, ... Close, but no cigar. <GG> The word is monococque, not monocoupe. But I think that term refers to a continuously connected structure like an...
Hi Geoff I looked in the manual but they only refer to the metal "shape pressed" structure as a "Inner Center Panel" and "Inner Side Crown Panel". I thought...
I found a tag that says this system has been charged with 50psi nitrogen. It is attached to a copper sweated line that goes up from the engine compartment...
They use nitrogen for several reasons. Leak checking is one, but it also keeps out moisture. Being inert it is a safe way to check, store, or transport a...
We would like to remind you of this upcoming event. New Members: Please Read Date: Wednesday, June 2, 2004 Time: 8:00AM EDT (GMT-04:00) If you are a new member...
RTS-bus-nuts@yahoogro...
Jun 2, 2004 11:47 am
10912
Does your pully have 3 grooves and is about 5 or 6 inches in Dia.? Geoff <nolids@...> wrote:Jim-- Did you get the pulley for me? I haven't heard from...
... Jim-- my current puylley has three grooves and is 1.5" wide where the belts ride. What I need is the pulley that only has two grooves to hold two 1/2"...
If there are heavy 24 volt loads such as AC blowers or Fluorescent lights, the 24 volt alternator is not charging the batteries more, it is driving the loads....
Your right Mike, We have large underground storage tanks purged with nitrogen gas. The gas is heavier then the solvent fumes that lay on the bottom of the...
Wulf P. Ward
wayward@...
Jun 2, 2004 4:21 pm
10916
How do you set the voltage on a one-wire internaly regulated Delco to accomodate the settings you suggest? And since most of the hand held voltage meters that...
Hi Monkey one, I see the same problem with the 12 volt charging off the same alternator. It uses the 12 volt coming off the r-terminal and that can not be...
Wulf P. Ward
wayward@...
Jun 2, 2004 4:55 pm
10918
Randy, If you have a separate battery not connected to the center tap of the main batteries, it is not critical to have the voltage set in relation to half...
Does anyone know what type of freon I would need to use to recharge my duotherm rooftop air conditioners? Thank you Danny Mickey's Back Yard Anaheim, CA 1986...
You do raise some valid points ... in spite of my joking around. It was after figuring out how the RTS system works that I decided to separate the siamese...
I've been looking at Dwight's picture of the aux fuel pump install intending to give him "the sincerest form of flattery". The rags in the picture hide the...
Dan It should be R22, there is a tag under the cover that indicates what type freon. Don ... __________________________________ Do you Yahoo!? Friends. Fun....
I'm ready to complete the wiring on the bus. I have my 50 amp shore power cord already. I have chosen a 6.5kW diesel generator. It's specifications a= re...
Hi Jeff, Just a little free advise from someone who did it 5 times. Your 50 amp shore-power comes in at 240 volt 50 amps per leg and your generator should be...
Wulf P. Ward
wayward@...
Jun 3, 2004 1:53 am
10926
Bubba-- Before you wire up the system go to the Xantrex/Trace website and download the manual for the SW4024 inverter-- they give special guidelines in wiring...
Thanks Geoff I have an electrician at work looking into this too. I was hoping for some ideas of the parts needed. I see where you got that switch from...
Wulf, thanks for the input. I meant to do both post together oops! I will look it all over. See what I can do about it. As in the other post to Geoff, I have...
You don't need to print out the whole manual-- you'll get one when you buy the inverter, just print out the pages that deal with the wiring installation. The...
It is funny that the person with the Odyssey condems marine wiring because it is not specifically approved for bus conversions (even though it is far superior...
Geoff, I plan to take a trip to Nimco today or tommorrow.I also need a two belt pully among other things.They have a whole room full of 730- 731's,hopefully...
