I just received a Invitation from Carlisle to Display my car in the Invitational Buildings ("T" & "Y") at the All Chrysler Carlsile Nationals on July 6-8. This...
Ralph, Hey, nice job. Hope you have a great time inside and out of the sun and heat. Cliff Ramsdell In a message dated 6/7/2007 9:57:01 P.M. Eastern Daylight...
mopartek@...
Jun 8, 2007 2:28 am
987
hello guys i bought one of those used belt tension gauges that some of you use off ebay but it have no paper work and have never used one so i was hoping for a...
I am looking for the owners of the following White 92 IROC R/T's: VIN's 3635 & 3640 I am only posting the last 4 of the VIN's to protect the privacy of the...
The one that was last in Virginia Beach Va in 2002 maybe the one that I got my Tlll motor from. Did it have gray leather interior? If it's the same one a armed...
Hi y'all, I am redoing the brakes on one of my Spirit R/Ts. Can't get the pistons pushed back into the calipers to allow room for the new pads. Tricks, tips,...
You could purchase a caliper tool (or even BORROW, a GREAT price) at Auto Zone for around $15-20 or use a big C-Clamp for $5-10. The real tool looks like a...
Eric, Once you have the caliper off the rotor, I remove the front pad and leave the inboard pad in place. Then use a large c-clamp that spans over the caliper...
Excellent reminder Ralph about pumping the brakes before putting the car in gear. You don't know how many times I've scared myself silly when I have forgotten...
Hi everyone, Need a little help. Changed the timing belt 2 weeks ago. Idle was rough with poor acceleration so retimed it yesterday. I was off by a tooth on ...
Hi Eric, If nothing else has changed, I would bet the belt is still not timed correctly. This can drive you mad, most of us already know your pain. _____ From:...
Agreed, one shouldn't need to loosen the bleeder fitting to spread brake pads, I merely suggested it as one way to eliminate any hydraulic obstruction farther...
Went to Sears to get a Craftsman spreader for $10. Passenger side was easy and came right off. Drivers side was frozen; I had to use a hammer to turn the...
I do not know what causes this, but every time I've gone to press in a brake caliper piston, it takes a lot of force to get the piston to move, but once it ...
I'm not sure what is wrong, but I'm quite sure the CHECK GAGES light comes on because of low oil pressure. At 250 RPM, the engine doesn't make much pressure...
I have 2 red 91 R/Ts that I am looking to sell along with a bunch of parts I have collected. One cars is rust free and very nice the other has rusty floors and...
I have the following im looking to sell. All are from a 93 IROC R/T had 118K when cam locked up in head. 1 568A Transmission 1 complete short block 1 Radiator...
Hey all, I was troubleshooting a leak in my a/c system and found the leak was where the unit goes through the firewall. I'm not sure what the unit is but when...
Hello Doug, I have a brand new Mopar NOS radiator for your Iroc R/T. I'm heading out the door for SDAC but give me a call on my cell for pricing. I won't be ...
What is a good source for starter heat shield? Has anyone tried universal/non-stock type? I used to get them at the dealer.... David B. Chester Las Vegas,...
I'm also interested in this info. My shield is still there but I would like to add more for piece of mind. ... Sent from my BlackBerry Wireless Handheld ... ...
As of 2-3 years ago, they were still available from Mopar. FWDPerformance carries one. I do not know how well it works though. There isn't much to them. The...
I use a Thermo-Tec Heat Shield Blank that wraps around the starter. It is sort of a PITA to get on, but it DOES WORK GOOD. I have one on my R/T and we have...
Cindy at FWD performance has starter heat shields. Aftermarket ones that do not fall apart and are the correct size for your car. Richard Paul (living in Hong...
I have 2 new RT radiators for sale. If interested, LMK They aren't cheap though! later, Cindy Cindy Lindsay www.fwdperformance.com 281-288-4411 299 Riley...
FWD Performance
sales8755@...
Jun 26, 2007 1:31 pm
1013
On the AC leak there are a couple of seals in there that may be leaking. Make sure it's not coming from any welded joints. You should be able to get them at...
Hey y'all... One of the t connectors leading into the vacuum ejector broke. Is this going to affect anything other than gas mileage until I can get it fixed?...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
