Anyone on board built one? Looking at making a manifold for my F+T conversion. I could buy one but building might be a good project. Looking for "Weld ELS"....
Im using a set of early style hurricane extractors on my N/A B230F 240. The #1 exhaust runner is different than on the sets available now. We entertained the...
Blackwoods (and most other industrial/engineering supply places) sell the steam-pipe bends you're looking for. "Weld-Els" is an American term, and most counter...
Built one for my Formula Vee many years ago. The maths takes a while, and the cylinder head will need to be removed unless the throat diameter of the valve...
Oh, and as to MIG welders, I'm no guru, but from my experience: DO NOT buy a gasless one - they're a waste of time, particularly on heavy stuff like exhaust...
A lot of decent migs are combination gas/gasless. Gasless wire is useful if welding outdoors when the weather is windy and the gas would be blown away. Also a...
... exhaust ports ... http://www.klracing.se/grenrorsflans.htm 400kr currently = $76aud. Not sure how much shipping would be, but it may still be barely cost...
Guys This site gives a good run through the work involved, ... lots. http://toyotaperformance.com/turbo_header.htm As Steve said TIG is best, but for thick...
Anthony Hyde
Anthony.Hyde@...
Dec 2, 2004 5:57 am
5778
Guys, We all missed out on this. Bugger http://cgi.ebay.com.au/ws/eBayISAPI.dll? ViewItem&category=2030&item=4506535663&rd=1 Steve...
cool link, being lazy i think i will spend the $$ for a set of IPD headers rather than continuing to entertain that fool notion i had of easily making a set...
... I've found a friend who has a nice TIG I might be able to use but if I decide to buy a new MIG I will ask for some details. Probably try and pick one up SH...
... our own. ... the exhaust ports Got a free head today :) Went to my local Volvo place to pick up a new expansion tank cap and oil filter and just happened...
... Time for some phone calls. ... They already look at me like I'm an idiot so it's not going to make much difference :) Seriously though, I often wonder if...
Hi all, I have a Brand New Hella Driving light Grill set to suit a Volvo 340 and 360 This was never a Volvo Option just a Option Hella made. It comes with the...
There was a guy selling stuff on eBay about a month ago who apparently had his wife kick him out, and he was really downing her with each item he had up for...
yeah, reminds me of trying to buy a wheel bearing set at repco. The slack lipped induhvidual looks it up on the computer and then say "we dont stock anything...
they appear well made in the pictures, so thats an option. I'd think you'd definately be able to have one made here for less than $76 AUD + the cost of...
Ash is right - last time I asked about getting something laser cut, the price was going to be the same for two as for ten... And that included them supplying...
Hello All, My 1973 164E is almost registered (got knocked back on only three trivial things). So, thanks to the wonders of the ACT rego scheme, I'm driving it...
Start from scratch and do a complete Tune. Set the throttle body as per manual (haynes will do) Set points to correct settings. Make sure ignition is good,...
The usual things to check in a B30! Valve lash adjustment Timing Cap & Rotor F.I. Points are set correctly Fuel Filter Air Filter (Probably ok since high RPM's...
Take the distributor to peices and clean out the old solidified grease that gums is up. Works wonders. /dlh. ... -- David Hallam in Queanbeyan Australia on...
MPS rooted??? MPS has dodgy wiring to it? air leak leaning it out down low? idle switch contacts dirty? No not the contact that is closed at idle, the one that...
G'day all What are the standard swaybar sizes for a 1979 242GT? I've been looking around for a while and can't find anywhere which tells me. I want to put them...
I think the '79 models had 23mm bars front and rear. Not certain of this. '80 and '81 models had a 23mm front and a 21mm rear I think. If you have a hard time...
What I forgot to ask is are they bigger than a '79 244's bars? I'd rather not import from overseas, like IPD simply due to cost. I've looked at Whiteline's...
Your '79 244 should have 19mm bars front and rear. I went from 17's, to 19's, then to 21's. There's minimal difference between them all, but if you can get a...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
