actually they fit 73 and earlier 140s as well. Bends in just fine with a little hacksawed from the middle flat mounting bit plus the ends. Would be even easier...
Greetings, i have some nice 740 alloys that i am thinking of fitting to my road car. Question is, will they fit without the offset fouling sway bars, brake...
Dear Group. I'm wrecking a 164e from 74 for its engine FI system and transmission. (Manual). Some other parts will be available. Email me off list if you have...
Wayne has asked me to forward this to the group, in case anyone is interested in a cheap 144 (for parts or restoration) (If I had the garage space, I would...
Gidday all, I am building a club race car and need a stronger diff, the Wolwo unit looks good because of ratios, discs and of course cost. The cutting and...
It's been a while since I've had the shafts out of one, but as I recall the shafts taper down slightly just before the splines, so if you were to cut the end...
Hi all, I've just picked up a 760 Turbo Manual. 1984 with B23ET and modified turbo. Its pretty crap, but the motor itself is good. What I need to know is,how...
Dennis B23ET - Perhaps an exciting aspect of your purchase might be the cylinder head. Check numerals behind #4 exhaust manifold to see if it has 530 OR 531 in...
Anthony Hyde
Anthony.Hyde@...
Jun 3, 2004 6:15 am
4639
Anthony, I'll go off the standard gauge once I get it running. I beleive the previous owner has blown the air flow meter. Whats the difference between the...
... Gidday Angus, If your memory is accurate then I'm a happy chappie. Thanks for the offer of the diff, really after something lower at 4.1 or 3.9. Fair old...
- Gidday Dennis, You mentioned fitting the Turbo engine to your GT, what type of GT, 242 I hope. I run a 242GT and have only recently got into Volvos again so...
No probs Les, 4.10:1 can be found in some '70's 240's, I've seen them in a couple of auto '75 244's, and also in a manual '78 245. Not super common but they're...
As i'm new to the group, and fairly new to Volvos in general, I may have missed some discussions. But my question is this, 16Valve conversions, is there anyone...
This has been covered over and over, many times on Turbobricks. Join the Turbobricks forum and search their message archives, you'll come up with heaps of...
that helps a great deal, thanks angus. But it appears that getting hold of one of these heads may pose the biggest problem, it aseems that they didn't sell...
hey everyone. i have just bought a 1985 760 turbo so i am looking to sell me 1972 142s. -it goes well, registered (tasmania) -rebuilt motor 15000 kms ago. ...
Has anyone here used Sach's "Super Touring" shock absorbers in their Volvo? I just picked up a pair of practically brand new rears for $20, and plan to put...
My 144 is being a pain!. The brakes drag very slightly and the brake peadal returns the last bit of its swing slowly. I've cleaned the master cylinder, Checked...
Have you checked the various return springs? I guess you'd have a new spring in your master cylinder and brakebooster cylinder. Though there is also one for...
Well if it is of any significance, it seems that often 100 series and earlier Volvo's which are seen in classic racing/rally, they often sport a Sach's Decal...
caliper seals could be stuffed/pistons rusted? I had to have my front calipers rebuilt as they were dragging a little and all the dust boots were torn. Later i...
I was really far into debt. Like Most I was in Financial dispair. I could not seem to get ahead no matter how hard I tried. Untill I found this place. ...
This may sound stupid, but did you check the pedal return spring to may sure it's attached & working properly? The calipers may be sticking too... -John In a...
just wanted to let the group know about a new forum at http://www.floridamigration.com/forum/ It pertains to florida vacation stories and tips. feel free to...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
