No ,I don't. Have a good day. Bob ... From: roycroft2004 To: MTCvoyager@yahoogroups.com Sent: Tuesday, September 13, 2005 5:33 AM Subject: [MTCvoyager] Wanted...
Hi all, I have had my kit about a month and am really enjoying it. It took a while to get used to how it handles but for the most part, it's great. I still...
Hi Reika. How many miles have you put on the Voyager kit. Work your way into the curves,you get use to them,just slow down too you get use to them. Take care...
Okay... I have put 1100+ miles on my Voyager kit (on an 05 Suzuki Burgman 650). I find the ride so hard that even small bumps cause it to rock violently from...
In a message dated 9/26/2005 4:07:26 PM Mountain Daylight Time, ... Erika I have one on a 98 wing. I can say I have experienced none of the problems you have...
Thanks Rick. I have emailed mtc but perhaps a phone call would be better. It does handle like a pre-load problem but we have run the full range of adjustment...
We've put over 5000 miles, including a 2000 trip from Ohio to Missouri for the BTW Trike Week, and havent found any of the problems mentioned. Ours is an 04...
Thanks for the feedback everyone. I may have found at least part of the problem. The installer pre-loaded the shocks on the Voyager and should not have. Also,...
Yippy-Skippy!!! I finally solved the bad handling problem. We lowered the Voyager tire pressure to 15#, removed the pre-load, and then lowered the pre-load on...
On a 1800 Goldwing with a Voyager kit the steering was hard. I noticed some of the trike kits have steering modifications would this work with the Voyager...
changing wheels is a pain..had to put new spindles on..old one only 4 inch pattern and car wheels are 5..just anyone was thinking about doing it..will send...
... A rake kit or a sterring dampener will not work with the voyager. Try to take the curves this way. Ease into the curve when the bike leans to the outside...
... Check the rear axle brackets the noise usually comes from where the suspension fork slides on the roller bearing. If the roller bearing is not rolling the ...
In the course of writing a commercial version of a motorcycle shop tracking database that was much more complex and sophisticated, I came across a small sized,...
I just installed a new Voyager kit on my 2003 LT. One of those jobs that takes a while the first time, the second time would take 4-5 hours. Drove it for 40...
I now have one installed on a 98 wing. We like it except for the low speed noise that seems to be comming from the fork and roller bearing at the axle...
... from the fork and roller bearing at the axle attachment point. ... Yes I just install one on an 2003 Honda Shadow Sabre. I like the kit just fine, but the...
Used Voyager for a H.D. 1200 Sportster needed.I'm disabled, on a fixed income & haven't ridden in 30 yrs.! Please inform me if anyone may know of one ...Can't...
I am disably retired, and purchased a Voyager Kit in May 2003. It was a great investment, as i thought i was going to have to sell "baby" prior to the...
egor franks
shovelheadguy@...
Jan 12, 2006 6:11 pm
52
please email if you have one for sale Thanks...
lancefaleshiacross@...
Jan 19, 2006 10:46 pm
53
Yes the instructions on the kit need work. I had to add wire on to my sidestand switch connections, this could have been in the instructions. However the kit...
roycroft2000
roycroft2000@...
Jan 22, 2006 1:09 am
54
A friend who has a Voyager on his Honda 1800 kept mentioning the problem he had with the fender bolts, his fender almost fell off while on the road. I just...
