Anybody going to Bike week? As cold as it is in Michigan today I'd LOVE to be planing a trip to a warmer spot, especially if it meant a chance to ride and...
So I'm in the middle of my Eldorado Automatic project. I pull the trans off of my convert drivtrain. If you look inside a Convert torque converter, there...
Mike: Its a freewheel device. Those pawls are intended to lay down and slip in one direction but stand up and grip in the other. That's why the Convert has...
Hey, I own a Guzzi Rosso Corsa, which I love, and am looking for a two up bike. A reciently met a nice older guy while riding who was admiring my Guzzi and...
no miles, no corrosion, might be worth 4-5 grand or more but I'd offer about 1500. and plan on a complete tear down to replace all seals and other rubber...
Hard to put a value on it "site un-seen". Where is it located from you? Keep in mind shipping cost. Running Verts will bring a large range of prices $1500.00...
Okay folks, I'm looking for some advice BEFORE I do something stupid (in contrast to my usual practice). One of the hex head bolts on my Convert's cylinder...
You could also try cutting a slot with a dremel and using a screwdriver to turn it out. Sometimes you can get a screwdriver tip to fit into the rounded out hex...
Oh, the bike is here in town and I won't even talk money with the guy until I see the bike. The guy I know who is freinds with the owner thinks the bike is a...
Are you talking about the sleeve socket nut? You say; "the hex key won't grab it" Makes me think you have it loose and just can't get it out!!! If thats the...
... OK, first, you're going to have to be a LOT more accurate in your description of the bolt and the location. Is it one of the eight, small, socket head...
which town? whats his #? I'll try and beat you there... just kiddin, post pics if you can. ... Don't get soaked. Take a quick peak at the forecast with...
Hi, AJ. I think the Convert is a truly excellent 2-up bike, as long as your power expectations are in line with its size and technology. The auto tranny and ...
If you do have the early type flywheel I will trade you the later version for it. it looks like its bowl shaped when viewed thru the plug where you set timing....
Well, I probably won't know for a week or more, the owner is recouping from surgery... I will post pics as soon as I get to see the bike. Apparently the bike...
"So in effect if this works out and I get the bike I would be the first person to register and title the bike." That would be neat! -Mike (69 ambo, 77 vert) ...
Thanks. That's worth 1000 words. BTW, is that a heavy flywheel? mtiberio <mtiberio@...> wrote: just uploaded... using guzzi factory tool w/chinese dial...
recently got the vert running, now I need to make it ridable. Does anone have a front brake lever for a 76 LAPD vert? Or, can the cast aluminum lever be...
I'm pretty sure they are still readily available from the usual suppliers, MG Cycle, guzzi Classics, Moto International, MPH, Speakers, Detroit Eurocycles etc....
I also need a little info on what is interchangable/usable from other M.G.s This bike is totally foreign to me, but it is starting to grow on me. What are...
Do you have a parts book?? if the bike is not charging there are a few things to check , take the cover to the stater check wiring(Yellow Wires) , the wiring...
... the cover to the stater check wiring(Yellow Wires) , the wiring was not heavy enough for the system (Some burn up the wires), the stater itself can have...
If the bike hasn't run in a while it will be worth just trying 'Flashing' the rotor. With the alternator cover off start the motor and then using a lenth of...
How about you throw them as far as you can and use a DYNA-III electronic ignition? Far better for keeping timing accurate. And timing is VERY important on a...
That's what I was going to say, so I'll just agree. If you tie the leads together you can really get some range :) In a message dated 3/19/2007 7:13:59 P.M....
