Joel, Those are very similar. The height looks smaller though. The M101cdn bump stops are not available on the open market (mil surp sellers, or other...
Spotted this in Stanton, Texas at http://www.samssurplus.com See pix in HRNCIR album. This is what our M101 trailer was built to be towed by. Gus Hrncir ...
Has anyone considered just making the bump stops. They only consist of two very simple pieces, rubber part and metal mounting plate. Based on the few that...
Didn't see an Iltis at that site but if you like government auctions there is going to be one in mid-October in Canada where 7-10 or so Ilti' are going to be...
I was answering a question about maximum up travel of a lunette over a pintle ( like when crossing a deep ditch) on another forum and dug up the photos of a...
Hi , I just ran across this site. http://www.northerntool.com/webapp/wcs/stores/servlet/ProductDisplay?storeId=6970&productId=200310619&R=200310619 Buyers 6in....
Hey dennis Have you been to this action before? Is it open bid? Any other info. They have some pretty nice stuff if you can get it cheap. To bad I am so...
Josh, No, I have never been to a Canadian auction but I saw a notice for this one and thought it looked interesting. It would be nice to have an Iltis to go...
I posted a couple of pixs from the Dixie Run at Tellico. Saw a couple of M416s in use at camp to but no other CDN2 M101s. PS. Bruce those photos a beautifull,...
I did just about the same thing and in the same place as Bill did. Using an Ebay purchased winch ($15) off of a small Chevy pick up truck. The install is...
Thanks! That is an option. I'm awating a few emails from various mfg'rs to see if they have something close. I'll be doing follow up calls/emails to them next...
These are great lights. One small detail... You do have to fashion up a GND connector for these, as they have 5 wires. GND wire can go to trailer GND. These...
FWIW http://www.jpmagazine.com/techarticles/70718/ I was thinking of a pair of these LEDs before I used Gamma Goat lights.The deciding factor: $. IIRC these...
Has anyone used these lights before? It would appear that the non retrofit ones could be easily flush mounted on the rear of a Jeep or the like. It seems that...
Bill, Your correct. They do mount flush on the version without the buckets. If you want to mount them in something like a humvee with recessed mounting,...
Hello All, I am hoping some of you electrical gurus can help me with this one. I am trying to find 2 or 2.5 inch round, red, stop/turn signals lights that...
... I don't think you'll find them. There is a DOT requirement that stop / turns must be a certain dimension. I think the minimum round can be 3". The 60...
No it would be for my jeep. For a couple of years I have toyed with "militarizing" my jeep. The act of cutting the huge holes for the HMMWV buckets in the rear...
Sounds like the LED tail lights might work out good for you then! I pickep up a set of them on ebay for $80.00 Mark ... From: Bill <jess_bill@...> To:...
I finally found LED Stop/Turn in 60 series red and 24 Volts. Put them in Charla's Cruiser this weekend. Now I really need to find those 2" amber LED turns in...
Bruce, On the way home I was tailing a municiple box truck. It appeared to have 2" LEDs that were being used as running lights. Not sure on the voltage, but...
Front or rear no bucket 185.95 ea front or rear with bucket 264.00 ea Black out driving light 154.00 I guess if they hardly ever go bad you have got make your...
Hello All I just picked up a set of new ones for the rear of my trailer as Im running it on both my 24v and 12v trucks so these will come in handy. If any one...
Todd, Are the buckets nesessary if you already have mil comp rear lights? Can you use youre existing buckets:-/? ... [Non-text portions of this message have...
Bill I did post some pixs of the lights and its guts . I posted them in the photos under Todd Os stuff The buckets are open inside and as for installing new...
