Joe Eish at Eish Enterprises has them, along with the tank top hats that Tom wanted. John Prusnek Hi all, MG Cycle is out of the rubber bumpers that they have...
Charlie, thanks a bunch for the pics. Nothing like a good visual. Ok, I have another question. The enrichener lever has a two-piece round base. The diameter of...
I've read that a tire valve stem for tubeless tires works well. It looks to me like it would, too. Rob, you have a stone? I didn't realize that. Charlie, it's...
I am knee deep in Eldo parts after tear down of my project and am in need of the following to complete the project. I have a 74, disc, civilian that I have...
Gerald, In your description you say your "in neutral with the clutch lever pulled all the way in". Are you sure your in neutral - the notorious neutral light...
Hi Gerald, Here are my "arm-chair" guesses: 1. Leak at the front is the seal for the timing chest cover. While you are replacing it, replace the gasket for the...
Correction, I'm not in neutral, I'm in first! Hello Loopers- I keep threatening dramatic rebuilds on my '72 El Dorado, but the experts on the list keep...
I was able to fit the rod in place with a bit of dremel work.... Ive sldo converted all nuts/bolts to Ss. My reco. would be to buy the Ss polished pak from...
Never had a problem with a condenser (knocking on wood), but then the one on the '69 is from my stash of 25 yr. old n.o.s. parts. We'll see how the Facet stuff...
One round piece is probably a spacer to raise the lever assy. up far enough that the lever clears the throttle twistgrip housing. If you can shoot a pic or two...
I have found what I think is the crank adaptor at Teo Lamers web site, please see the photo section under "Mike's Bike" to confirm I have found the right part:...
Hey Guzzi Gurus! While removing the rear fender, I noticed that the front edge of the fender was binding against the cross member of the swing arm. I barely...
That would be the one you need. http://www.thisoldtractor.com/gtbender/loopframe_loop_list.htm Paul 73 Eldo "Elvira" 949 conversion with hack 83 1000SP NT...
hello, just got in a trade deal a red barron fiberglass cafe kit for a tonti frame guzzi, does anybody know what it is, where its from, i never saw one like...
When I rebuilt my carbs, I couldn't get the slides to go all the way back down even with all new cables. So I beefed up the springs a bit but they still don't...
Mike, on the slides, make sure they are in the right way. If you look inside, one slot is shorter than the other. so if you put them in backwards, they will...
Hi Mike, I'd check with Mark @ Moto Guzzi Classics before you buy the MI/Teo Lammers one. At the time I bought mine Mark was working on having a batch made if...
Mike, If you are sure the slides are not returning, I had a similar problem and it turned out to be gunk in the throttle hand control. Just took it apart and...
Too beat to even think about going out to the shop tonight. Will take pics of the assembly bits tomorrow and put them in my Photos folder. Thanks. Ray ... ...
... Yes, everytime you have your swingarm powdercoated You will have to remove them for the powdercoater. A 400 degree oven and a greasy bearing will...
The top of the carb can only go on one way, so if you see which way it goes on then you should figure out which way the slide should be installed. You want the...
You and me both Charlie! Never got a bolt or washer with mine either, plus it took over a month to get it. Learned my lesson, next time I'll call Mark first. ...
The one from MI is the same as the one from Teo. MI is Teo's exclusive distributor in the States. MG Classics bought theirs from MI, so they're all the same. ...
II rmoved allmu bearings beefore p coatings. s ... II rmoved allmu bearings beefore p coatings. s --- In Loopframe_Guzzi@yahoogroups.com, "Steven Anspach"...
... and/or evenly is ... Sorry about posting late on this thread....haven't been able to keep up, but Ray brings up a good point. the finest torque wrench in...
It allows you to use an alternator crank (with tapered nose) together with a loop frame style timing cover/fan belt. its a quick and dirty way to get an oil...
Speaking of float numbers, etc...I've added a bunch of Dell'Orto and Amal info to my website that I've scrounged from various locations around the internet....
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
