I've always mounted and balanced my own tires with the dot by the valve stem, here's some cut and paste from a couple of sources on the web, for further...
I guess I'll be the one to jump in and commit heresy and question Marks design, never the while forgetting that custom creations (or any more humble attempt...
This is what Mark wants to hear, your opinions and comments your likes and dislikes about his creation. He didn't go into too much detail and the u-joint...
I've got my frame completely torn down & ready for paint except for one thing - I can't remove the fork lock. I drilled-out the rivet & removed the little...
Hi Marty, Here's a link to website that your locksmith might find helpful: http://www.softcom.net/users/w6rec/duane/bmw/keys.htm Loop fork locks are made by...
Thanks Charlie - I'm going today to try-out the only other locksmith here in town who doesn't work out of a van. If that doesn't work I'll try the drill, as...
... YES. Is there a number visible on the core? Perhaps we can find another Loop rider with the same number and he can loan you a key. You could always just...
Thief River Falls, Minn. Arctic Cat today announced plans for a new 750 Series of utility all-terrain vehicles (ATVs). While not yet developed, this represents...
I think I started this thread. This is the statement from Greg's instructions that initially threw me "On Bosch-equipped machines, you cannot just disconnect...
Am repowering my 1989 Cub Cadet at the moment with a new Honda 24hp v-twin While surfing about break-in I ra across this interesting site. Yu will notice down...
I rode the Eldo to work pretty much all Winter and you would think that after 3+ years of fettling I could just gas it and go. Not so I'm afraid. About a year...
Hi All , I have the trans out and and getting ready to call MG for clutch parts . What else should I do since I am this far ? seals ? ho , does any one...
Marty, the lock comes out with the key. A competent locksmith should be able to pick the lock (if it's not frozen) and remove it, then make you a key if he can...
Marty, Just wondering here; why don't you dollop a drop of hot-glue on the key cylinder and after the paint job is done rip the dollop off and you can do what...
No, no numbers at all. You'd think there would be, wouldn't you? I'm letting another (more optimistic) locksmith give it a go, but yes, replacing it is an...
Dave, That nasty stuff is pretty common on batteries that have seen some hardship and have begun leaking at the posts. Best thing to clean it all off with is ...
I considered putting something over the lock, but I figured it might melt or otherwise interfere with paint. Besides, at this moment, with EVERYTHING stripped...
It will cost you less money to drill out the old one and replace it with a new one that comes with 2 keys than have some locksmith spend a few hours trying to...
Thanks Matt - I really appreciate your confirmation. I was 95% sure that it would come out with the key - I really couldn't see any other way - but you never...
You may be right - I paid the first guy $20 for the blanks he used up trying - we'll see what I'm into the 2nd guy for. Do you recall what you paid for the...
I love it!!! What more can I say. My only question is, where did Mark get those spokes to lace up the rear wheel? Cory ... likes and ... my mind as ... ...
Spent 8 hrs today beefing up swing arm,welded tubing same size top and bottom of both sides of swing arm,looks stock only bigger and stronger,tank is just...
Had that complete rusty ugly wheel lying around for years,allmost threw it away several times,spun it and it was true butt real ugly,sent it to powdercoater...
Hi All, any recommendation on where to get a piston wirst pin puller as seen in the Permier Motor Corp Ambo Manual # 17 in the tools section ???? Thanks ...
I made one out of a PVC pipe nipple, a 3/8" stove bolt w/nut and some washers. Ground the head of the stove bolt down to the same diameter as the piston pin...
A lot of folks in the northern climates are just getting back onto two wheels, thinking about summer trips and rallies. I thought maybe it might be timely to...
