This file contains the posting guidelines, or "house rules" for the "Locost OZ" mailing list. It is auto-posted once a month to the list, and is sent to new...
Locost_Oz@yahoogroups...
Dec 1, 2004 10:54 am
8889
Al, there's plans on my website for a welding cart. I made it from scrap I had on hand. Think there's some other ideas on Peter Ogden's mirror site. A couple...
There's been lots of mods done to this intake to lower it, including chucking it and replacing it with straight pipe and runners. Don't think the engine cares...
Steve we'll I'd be keen to come out to Mawson on Sunday arvo and check ouy your build. Don't know if anyone else is about. Can we say 2 PM again? Andrew We can...
After my 12 week TAFE course, I built the regulation welder/gas bottle trolley, and then an engine hoist. The Hoist is essential and has seen many an engine go...
Yep, 2PM is OK - 46 Hurley Street, ph62861059. Might get a few yet. Build isn't going so quick, too much other stuff to do, but will soon have a big billy-cart...
I'll be there. Dave Jones Yep, 2PM is OK - 46 Hurley Street, ph62861059. Might get a few yet. Build isn't going so quick, too much other stuff to do, but will...
Hi Carl, If you are in the Vic Builders group and coming to the bbq on Sunday get a set off Geoff. Otherwise Yesterford in Bayswater has them as cheap as you ...
Both charge around $68ea from memory. You could also go to REPCO, they were only $198ea last time I checked. If you are going to get them from Geoff I would...
Hey mate, I have 2 new rod ends for the transit you can have for $40 NZ each. They have an M20 thread, not the M18 as specified in the book. I bought 4 because...
Thanks for the offer but the M20's won't fit my car. I am only looking for one, I managed to mess one up a bit. The M20 transit rod-end fits the top on the...
Hi guys I am going to shorten my rack to improve bump steer, there doesn't seem to be much info on the web (that I can find). Has anyone got a definitive...
Hi Patrick, I have shortened 3 or 4 now and have one more to do in the shed at the moment, ....1 was at 98mm, his set up was a bit odd though, ....1 at 110, ...
g'day Patrick, Paul H is the man for that stuff - the only thing I'd add to Paul's reply is that the exact rack width required to get optimum bump steer ...
My apologies, forgot Charles', at 108...add one more to that total. Paul H ... From: "Charles Hoffman" <choffman@...> To: <Locost_Oz@yahoogroups.com> ...
Hi Patrick. Work out the height for the rack - draw a line between upper and lower wishbone mounts on both sides - measure the distance between the lines at ...
Hi Patrick Something to keep in mind with a shortened rack , it moves the steering input shaft towards the centre of the car by half the amount you've ...
Paul, As I recall these racks start out at 600mm in length? Or is that the Cortina? ===== Geo. Cushing, Delanson, NY, US http://www.georgecushing.net...
Thanks for that Paul Simple is good, atleast nothing is left out. I did the straight edge between the susp pivots earlier this morning, the rack came out to be...
Hi all, I have checked out Paul Hannell's speedo drive conversion, from T50 to AE101 (AE111 in my case) My T50 drive is unlike the one in Paul's pictures, as...
Sorry for silly question, but are you sure it is a T50 ? Paul H ... From: "emexv" <emexv@...> To: <Locost_Oz@yahoogroups.com> Sent: Monday, December...
Greetings all! Is it possible to mate a T50 gearbox (20 spline) from a 2T/3T Celica to an "A series' bellhousing to enable it to be used with a 4AGE motor? I...
Yep, as far as i know, it is a T50. I have looked at pictures online of a T50 and that seems to confirm it. Did earlier/later versions vary in the speedo...
Hi Padraic, With out sounding like a smart a**e, yes anything is possible. Check the length of the belhousings to see if the clutch heights will be similar. Do...
They may have, I have done about a dozen of those conversions now, and all have been the same at the document I did up. I even have a couple of the rightangle...
... will be ... block, or if ... welcome to ... adaption if ... Paul, from my observations it would appear that only the 'top two' holes on the block, and...
