I have a friend who might be interested in your project. He is not currently a member of the list, so he cannot see the photos on that section. He can be...
If you put the diagonal tube ends to the middle of the top rail, you put a beaming load into the top rail. Meaning that when the chassis flexes, the top rail...
you can say that about every point where a tube is welded to the top rail. You would be right if we were hanging a mass in the middle of the beam, but i am...
Hi list - I'm looking ino buing a nose cone for bookish chassis. I thought I'll get the COLD nose but it seems the splitter goes too low for my ground...
Moti-- I am puzzled . I have a CMC nose from Kinetic and it fits my BOOK chassis just fine although I will have to whup a lump in the hood to house the 4A-GE...
Not if there is a vertical tube next to it. Esko ... From: Anthony To: Locost_North_America@yahoogroups.com Sent: Wednesday, October 01, 2008 5:28 PM Subject:...
Have you ruled out a Curtis Unlimited nosecone? If not go to Greg W's "Lethal Locost" site and look at pictures of one on a mostly book frame. If you need...
The top two pix show an earlier 2hp Lauson in my Rollfast. The clutch and brake are clearly shown as is the bike generator that runs on a clothes dryer drum...
GEEZ I appologize for this screwup. I tried to use an HP program to email 4 pictures to to a motorized bicycle club and inserted the proper email address...
No I haven't, the opposite is true - I was looking for tips on other vendors ... I'll check the Curtis nose out. Keith - not sure what puzzled you, but...
How about taking and inch or two of the the Kinetic TTL? ... From: Moti Almagor <SR71Miata@...> Subject: [Locost_North_America] Nose cone sources To:...
Sorry, I meant an inch or two OUT of the Kinetic TTL. ... From: JEB Thornton <kill_no_cone@...> Subject: Re: [Locost_North_America] Nose cone sources To:...
... Like this? [IMG]http://img.photobucket.com/albums/v356/Grintch/Vbrace.jpg[/IMG] This is pretty common with British 7 variants, even the Caterham CSR seems...
Bruce- I can possibly do that but I have a 3/4" square tubing running from about 4" above the bottom rail at the angle break on the side to the top of the...
http://www.nytimes.com/2008/09/28/automobiles/28LEMONS.html **************Looking for simple solutions to your real-life financial challenges? Check out...
To save the splitter and still reduce the height ,take the required height out of the middle of the sides and glass the top and bottom halves back together. ...
I have an extra nose cone. It is from CMC, and they actually did a pretty good job at it. It also appears to be a direct clone from a Lotus S2-ish nose cone,...
[I don't think this went through the first time...sorry if this is a duplicate.] http://www.youtube.com/watch?v=ap9bsNJJgd0 (BTW, it gets really fuzzy about...
Thanks. If you can send me a couple pics off list I'd appreciate it. What height is the nose assuming the part that leans on the rails is parallel to the...
... My pleasure! You know you're my inspiration for the whole "drawn and quartered" bit! If I'da been smart, I would have sold the tub, but how in the world...
I'll see if I can get some pics. The height of the center above the top rails is approximately 7.5". Esko, you have 2nd dibs, but I really don't want to have...
Dr. Hess, If I get the purchase, I can send you the right size box folded, All you would have to do is to tape the box together and put the item inside and let...
Keith Williams wrote: I tried 2 parts stores so far. Not beat yet. KW Back when I worked in auto parts stores, we had a large assortment in a plastic box. ...
I asked about one at the parts store but they said 18mm plugs are obsolete. I still have a few more stores b4 I look for cu. or split some cu. plumbing...
