Greg, How was the quality of the nose? I have heard different testimonials about them. Was it a heavy lay-up or was it "lightweight"? Esko ... From: G Wellwood...
Hi All: I just preregistered for my first autocross in my se7en. I signed up for emod--I hope that's right. Anyway, how are you guys attaching numbers to your...
Chris, I have a vinyl number plate that is on each side of the car and one on the nose. I have individual numbers that I can put on the plate however. I am...
Hi Jeff: How does the vinyl number plat stick to the aluminum? I can my my print broker print some up for free. Also, do you use loose number in case someone ...
Chris, The plate itself is actually a decal. The numbers are karting numbers that are low tack for easy removal. You could probably get the same type numbers...
Hi Jeff: Thanks. Looks like I my printer may not be able to turn the job in time. Am I allowed to print the numbers off on paper, then use painter's tape to ...
... At the one and only autocross I've run, I borrowed some blue masking tape from the guy next to me and just made big stick-figure numbers on my window...
Hi Chris, Some people use blue painters tape to make their numbers for the side of their cars. I have a permeate number for my car and the club I run with and...
Chris - Numbers can be a delicate subject in some areas but not in others. I would check and see if they have any minimum requirements for the size of the...
Hi Chris. I use the vynil for lining drawers etc (white) and the largest numbers available (6") at hobby supply places. The vynil is light adhesive and can...
On the Leitch 23B replica (http://home.earthlink.net/~earleymotorsports/sitebuildercontent/sitebuilderpictures/23bchassis.jpg) you'll see a substantial panel...
A better pic -- http://home.earthlink.net/~earleymotorsports/sitebuildercontent/sitebuilderpictures/23bcockpit.jpg Uh, thank you Early Motorsports... Tim...
... get-together. Any one else. GTA, Southern Ontario, Upper New York State, Buffalo ? Or vica-versa. George 1129 ... Be smarter than spam. See how smart...
Sure, I'm on for a get together in or near the GTA, ie.close to home. A Seven, at least mine, is not the most comfortable for long distances on 4 series...
I'm in for another GTA get togeather ! Bob MacLeod ... From: ptrxly <ailsa@...> To: Locost_North_America@yahoogroups.com Sent: Wednesday, May 2, 2007...
I have two car shows to go to this weekend and go look at KU's formula SAE car and it is suppose to rain everyday. This SUCKS. Why can't I live in the desert?...
Even if you live in the desert, it rains when you want to get a Seven out. It's the weirdest thing, the car causes rain. Keith ... [Non-text portions of this...
Gents: A dumb question; I admit. But I'm doing last minute autocross prep stuff... I went to remove a rear lug bolt today and to find it got stuck on the ...
It's either a 29 or 32mm if I remember correctly. There were two different sizes. You're in the ballpark for torque, it's right around 200 ft/lbs. Keith ... ...
... My shop is available. Three Locosts and an Elan in now. (St Catherines) GTA and a pub or Buffalo and a bar is still good for me. Last one was East, maybe...
... Missing a lot of fun at low speeds. George 1129 ... Be smarter than spam. See how smart SpamGuard is at giving junk email the boot with the All-new Yahoo!...
It's a Seven thing. It's originally a Brit car, of course. The big kitcar show in the UK is this coming weekend. It's been sunny all week. Rain is forecast for...
Yes I drive in the rain. And yes I will not do that again after my last trip. Life is too short. At least I have wipers now. Still no top or doors. Dripping in...
Finally, I am starting to fabricate doors for my Deman Motorsport SR7 and am looking for a supplier of 1.5 to 2mm thick aluminium sheet at reasonable prices in...
I'm getting enough of my frame tacked together to start thinking about positioning the engine. I'm putting a chevy 2.8 V6 in a 442. Fore and aft positioning...
Tim, I would suggest getting the custom oil pan first, so there would be no guessing (i know waiting for parts can sometimes be the worst part). I'm using a...
I got all my steel and aluminum from Boss Steel in Richmond Hill. http://www.bossteel.com/ See David with cash money for a better deal and tell them I sent...
... Cool! I was expecting a lot of nay-saying. I'm pretty sure I won't tackle that myself. Any guidance on what kind of shop I should take it to, or what...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
