Lance, Thanks for the info. I assume the motorcycle you had shipped had to be drained of all gas, oil etc and strapped to a pallet? Did the seller do it or...
Since the 2L motor is now back in (but not yet fired up) I thought I would "test fit" the FI intake components. It's really tight... the TB body throttle idle...
I found an NOS gasket/spacer and it has a thin paper gasket on each side of the spacer. I was home for less than 24 hours yesterday/today after towing the RV...
Barry; You can run without the spacer if you don't need to bolt up the bottom tang, but I'd keep the spacer b/c the runner holes don't line up without it (the ...
Is there ever any clearance issues with the FI manifold and the alternator? From what i understand, you cant use dual carbs without moving the alternator down...
No clearance problems with the FI manifold, Jason. But you'll want to nake sure you have a really good starter in there because you DON'T want to have to...
Fellas, Thanks to the so cal fellas for finding a place for dinner and thanks to Luis for offering his home up for a party. The best of my understanding is...
... Screw it all the way in. Mark it. Cut a good chunk off of it off, slot the end with a dremel if you'd like, ditch the spring, and simply fit a jamb nut. ...
Andrew Ring the ticket hotline - 0121 767 4767, and quote reference code CLX. Don't forget also to leave your ticket stub at the Consortium stand (stand 4160)...
Although I agree it's best not to dent the firewall, I'm not sure what slotting the end of the cut off screw will do for you since it's difficult to get a...
Jason, If you are OK with the friction style LSD then Colotti used to make them for the Scorpion, and there also may be other sources. If you want to go with...
Jason, If you are OK with the friction style LSD then Colotti used to make them for the Scorpion, and there also may be other sources. If you want to go with...
There are a couple of other possibilities as well- from the Phantom Grip on the cheap end to buying one of the cheap Quaiffe clones (Like the OBX at around...
Come to think of it, aren't people always saying the Alfa 164 diff is very similar or identical to the Beta? And wasn't there a LSD 164, in addition to a 4WD...
I believe that the Alfa 164 diff is very similar if not identical to the Thema. So it *might* be possible to install a 164 LSD in a Scorpion transaxle by...
I am planning a turbo FI 1.8 for my scorp. The main reason I am looking, is for our x1/9 racecar thats getting a 2.0 twin cam. The alfa diff would be great if...
I am planning a turbo FI 1.8 for my scorp. The main reason I am looking, is for our x1/9 racecar thats getting a 2.0 twin cam. The alfa diff would be great if...
For an X-1/9, the Phantom Grip DOES FIT AS STOCK, and is a pretty easy install (put it in, pry the little clips off and hope they don't poke your eye out)....
But let's just say the mornings are getting 'crisp' out here, my god I actually found myself wearing..gasp...SHOES the other day, don't tell my buddy...
Our race x1/9 will have a scorp transaxel, so i need to find out if it will fit the scorpion. Jason ... easy ... poke your ... fitted with a ... about two ... ...
The Phanton Grip works by using the inner faces of the output shafts as a metal to metal clutches, preloaded by the springs of the Phanton Grip. Wear occurs...
Couple of point of dissention Tom: The PG is smaller than the OPM , which is functionally virtually identical and which works the same way (preload type)....
here is some info taken directly from the OPM website. "The OPM limited-slip is a patented clutch-type custom made limited- slip differential. We start with a...
Jason; There was an incredibly long thread on the Honda forums about OPM vs PG vs Quaiffe, etc. On page 4 there are pictures of the Phantom Grip, OPM, and AZ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
