Hi Craig! Some head gasket brand/manufacturers says no need to retorque mostly those with sealastic and other proprietrory design they incorporate in their ...
Question for you engineer fellas, Why can't you lay a refrigerator on it's side while moving it? I sold my old farm truck as it was on it's last legs, leaving...
Couldn't send this direct to you, Mike; .......................................................... You CAN, but if it's an older fridge you need to open up the...
Never had that problem, but as they say, (I ) learn something new every day. Another link says just wait an hour before you plug it in- of course if you are...
Patience is a virtue as I've been told (and never had) and I appreciate all the patience of those who ordered the CSC Exhaust systems or headers. I have been...
Hey Tony, That's great news!!! Does Racing Beat also have "the list" so they'll know who's paid and who actually gets what? Thanks John O. ... -- No virus...
They will have the list of purchasers, the addresses, and what goes where, by next week. Tony F ... and who ... arrive ... will ... say ... collected ... ...
Eddy, I ALWAYS retorque the head after the first heat cycle, even if the gasket manufacturer says it is not necessary. I have never had a head gasket...
You can lay a refrigerator down, BUT it must be allowed to stay unpluged for a few hours once it is installed. The liquid refrigerant will flow into the coils...
Michael, You may lay it on its side for a very short period of time. However, it is mandatory to keep it errectecd for at least a day or so before you plug it...
These guys seem to agree with Craig, but the consensus is to let it stand for 24 hours to let the oil run back down into the compressor. Best thing is to not...
From: Jen Bentley et al <uunet!poe.acc.virginia.edu!jbb3z> Date: Tue, 30 Jul 1996 01:31:17 -0400 (EDT) Subject: MR2/Ferrari Early mid engine Ferrari's are dime...
Maybe this is only applicable to Old-skool freon units with the R2-D2, er- I mean R-12 compressors ;) I put in two O/U units last year and they BOTH shipped...
... <harfkanarf@y...> ... Mike, I suggest that you take this, now long, thread to the Yahoo Groups 'Fridge site'. I am sure it would be one of their "hot ...
Are there any tips for replacing a head gasket on a scorpion? Tommorrow morning will mark my first head gasket replacement on a scorpion(been a scorpion owner...
All, No response to my request to the group on the subject of differential bearing clearance/pre-load. Maybe all the cold beer in the working refrigerators is...
Hi Lonnie! It is not that we are giving you the cold shoulder from Mike's refrigerator, It is just, in my opinion the "most critical and precise" adjustment in...
1st year that it was held. Over 150 cars and bikes. Three ladies rolled up in their Ducati's. 1 Ferrari 430 and the newest Lambo and Maserati's were...
I didn't see the yellow/red GTV in the pictures? I did wonder about the white Countach though, mostly about: a) Why he's trying to do a chin spoiler's job with...
... ////////////////////////////////////////////////////////////////////// I figured you probably could with the proper precautions. I'm just looking at ad's...
Best thing is to not lay it down at all. ... /////////////////////////////////////////////////////////////////////// I'll get a body saw and turn my cherokee...
Lonnie, Sorry no Haynes manual, but the procedure is explained in the Beta shop manual (but without the specs). The Scorpion Technical Data sheets have both...
Peter, I am copying the Scorpion group and others to share the subject. ... Reply: ==== This is terrible! It should not move out at all even with high ...
Peter, I had this happen on my car, too. Couldn't keep a seal in one of my camboxes. I remedied it with some special "Bearing and Seal" retainer liquid that...
DJ, Thanks for the tip. Maybe I can save myself some $/time. Peter DJ Richards <dj@...> wrote: Peter, I had this happen on my car, too. Couldn't keep...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
