Hi Bob; I believe this is the answer to your question. Kawasaki Part # 12048-1113 Tensioner Assy, Part # 11009-1858 Tensioner Gasket. I Believe Ron Ayers has...
Yes............that is the part# from a ZX1100 1990 onwards This E Mail signature attached to the end of this message verifies the source is genuine and that...
Go to ronayers.com and select OEM and microfiche and select the ZX1100 parts list. This E Mail signature attached to the end of this message verifies the...
No problem............I forgot to mention the first time the part# was the ZX1100. I think if you look up various years they all have the same part#....
remember that now it's adviced to use the APE manual tensioner instead of the zx11 spring tensioner, (the spring is to strong and the gears are plastic and...
which means??? Horacio Colombo <horacio.colombo@...> wrote: remember that now it's adviced to use the APE manual tensioner instead of the zx11 spring...
Where is this APE tensoner in stock ,Kawasaki part or aftermarket part? I just need to now where to buy or order it from part # if avaliable Horacio Colombo...
Use caution when messing around with the CCT. If the chain Jumps; to quote Dante: "Give up all hope ye who enter here". O.K. maybe thats an overstatement of...
Dear Readers I am just checking through a new 1300 that I bought. It wasn't running and had no battery. I just bought a battery and hooked it up with great...
Hi, Please don't take offense to this answer but, I know many experienced riders (including me) that were burned by this. Check the key under the seat (i.e....
Anyone had problems with an oil drain plug that will not move? I don't want to force it too much in case I round off the head or even shear it. I have been...
I've finally finished welding up the coolant pipes for my radiator relocation project. All I've got to do now is find some 90 degree pieces of 1 3/8" radiator...
... wrote: Well, I did learn a bit more about the intricacies of KZ1300's. Did not know about the under seat switch. I put battery in and turned to the on...
John, If your battery is good try the main switch in the on position, transmission in neutral, pull the clutch and hit the starter. I can't believe that every...
Use an impact gun and hit it with brief attempts. Use a like new good quality 6 point socket such as a craftsmen or S&K. I've had this problem myself before...
I have a 1980 kz 1300 with 17000 miles on her. When I try to crank her oil and gas start pouring out of breathing tube that goes from the engine to the air...
Hi John, Sounds like you've had gasoline drain from the tank into the crankcase. Can you still see the oil level in the sight glass? Bill R ... her oil and gas...
Thanks Dave, I'll give that a try. It just wont budge with a normal socket and wrench and the other problem is if you do not keep the socket straight you can...
How about applying a bit of heat to the surrounding area with a small torch. **************************************Check out AOL's list of 2007's hottest ...
... Leaking float valve assemblies in the carbs. Sounds like the sump is full of petr-oil mix. If the sight glass is full, or you smell petrol in the oil...
Your tried a new battery and turned on the seat switch. Check that you have voltage to the switch and out of the switch. You can use a volt meter for this, or...
... The switch under the seat has a third position, that of "parking lights only" (that's what we call them in Oz anyway). Let's face it, you're going to have...
Hi Dave & Jim: Thanks for your suggestions on that oil drain plug. I was going to try each suggestion if one or the other did not work at first. I did buy a...
Hi Sometimes the switches under the seat gets a bad connection, try spraying some contact cleaner and wiggling it...almost sure the problem is there, otherwise...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
