maybe you should mention the fact that almost every police force in the country uses motorcycles in law enforcement. and here in the South it is almost year...
Hello Friends, With the gas prices as high as they are $3.90 a gallon in Iowa.We are seeing more and more bikes mopeds etc.. on the roads.I dont see how anyone...
"and all the plain ol' fun you have dodging all the cell-phone distracted, i-pod infested, latte' sippin' cager's! But I digress." ... Dale, I had alot of the...
Fernando Llambias, I'm hoping you are in this discussion group because your email system is rejecting my replies to you. This is the failure notice I got back ...
Does anyone know what colors were used for the KZ1300? So far I have seen pics of Green, Black, Red. It may be the some of the colors I have seen have been...
... My '80 KZ1300A-2 (which found it's way to Oz via Sweden) is still the original "Red". My '84 ZG1300 DFI (imported from Japan to Oz) is still the origuinal...
Hi In SA we had the three colors Red,Black & Green, but in addition the pin striping differ from model to model. I have some pics that I can mail of some of...
I'm having a small problem with my clutch. I've adjusted it several times but it still likes to jerk a little when engaging 1st gear. Possibly stuck plates? I...
It happened to me some time ago, every time I started the engine (almost always cold). I suggest to change the oil brand Regards. Horacio Lic. Horacio R....
New battery?? it seems that when cold, the battery barely does its work but when hot is a little more charged and works fine Regards Horacio "daggerdarts"...
Sorry its not the BAT!! Used a New car Bat.. Melted the the relay.. then rean stret from the bat to the stater, still runs slow .. The third KAW 1300 I have...
... A few things come to mind. 1. If it's worse when th engine is cold, it may be the oil is too heavy. 2. The plates have gummed up a bit and need to be...
... Could be you have a few shorted turns on the starter motor. This will draw more current but give less power out. Due to insulation cracking on the coils....
... several ... everything ... miles ... needed. ... heavy. ... of ... (effectively ... coming ... distort ... without ... come ... the ... I may swap out the...
... Clean the plates with a solvent such as (Wynn's) Injector Cleaner. Leave the steels smooth, just use steel wool on them. I use engine oil - 10W40 in the...
I'd advise against the gearbox oil as you may not get sufficent pressure to the valve train. I use 20-50 Mobil1 right here in Seattle year round. Dale S ... ...
If you are running any type of cam chain tensioner in your 1300, read on.(Should be ALL of us, unless it ain't running) Disassembled the head and cylinder off...
I have a complete 1980 sport model and a spare parts bike thats about 60% there. Located in Rochester NY. $1500 takes it all. Photos available. Send Email to...
Mine had 72,000 miles when the plastic sprocket wore down to nothing, could it be too much tension? who knows, I tend to think it could be but also the fact...
... Just for comparison, I have one original timing chain sprocket and chain tensioner combo which shows little wear at 260,000km (about 160,000 miles) and...
Hi Dale, I'm running the APE CCT and so far no problems and since its nothing more than a bolt the pressure is constant. I'm guessing that this configuration...
Now where cooking with gas!! I well take a Look Thanks R Re: KawaSixes. NO!! its not the Battery ... work ... fine ... Could be you have a few shorted turns...
Eastwood, (www.Eastwoodco.com)a <http://www.Eastwoodco.com)a> major automotive repair/restore/revive supplier, carrys the House of Kolor paint line. Altho it...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
