HI, thanks for the info, yeh i will give that a go, at worst it will whine if the chain is too tight!. At the momnet its snowing, so i wont be heading out to...
      Know this has been discussed before, but cannot remember if correct seats are supposed to have contrasting piping around the seat? ... From: Tom...
... is that it is white or silver. Ebay #160311254568 is the only seller I see. I have purchased several covers for my bikes from several makers and a couple...
... colored piping on the seat: http://www.spookytoms.com/CB125S-IDPlates.html. ... correct seats are supposed to have contrasting piping around the seat?...
I have bought about 5-6 of the covers from the supplier in Canada on ebay known as gumtwo... his covers are quite close to the original, and if installed...
Hi, the seat covers originally would have have piping around which is clear plastic with a braided silver liner inside. Over the years the sun sends the...
... edge moulding. Thanks. ... clear plastic with a braided silver liner inside. Over the years the sun sends the outer clear part yellow, so appears to give...
... thicker but gives a nice radius to the wrap ... clear plastic with a braided silver liner inside. Over the years the sun sends the outer clear part yellow,...
      Door edge guard isn't registering. Maybe that is why all the edges of my doors look so dinged up? Please a description. I ask a lot of...
Door edge guard (for auto purposes) is a "horseshoe" shaped often chromed plastic strip which is put at the edge of the door to prevent dings in the car next...
... particular ... you ... (reproductions, ... It just so happens my sets of "Ohio" boots have arrived, I have managed to get them on with no problems,...
Hi, well if your importing them from a freind in USA, theyre not new- its a gift ;) regards Robin ... From: pete.monks To: Honda_SS125A@yahoogroups.com Sent:...
... its a gift ;) ... That's true EXCEPT the UK Customs and Post Office operate a screwy tax system. The last time I checked buying a new item, from a ...
Hi, Well ive bought two lock sets from USA, and even with importation duty it works out a load cheaper than buying from any NOS supplier in UK or Europe.But i...
Hi all, im at the stage where im sorting out the carburettor for it and i have found that it has been warped from over tightening. Im thinking perhaps some...
where was it warped? mounting flange? that is a pretty thick piece of metal...hard to imagine it bending....I wonder if you wouldn't be better off sanding it...
HI Ben, I did think of that, but with the amount of bend in it, it would be very obvious. I put it on a flat surface and there is about a 2mm gap. Yes the...
Brasso metal polish on the choke lever and other metals bits. ... very obvious. I put it on a flat surface and there is about a 2mm gap. Yes the flang area. ...
There was a time when Japan was looked at just like China is now... working hard to improve products and manuals, but still not quite there. Read this: Taken...
ebay item 170299842716 - don't forget, even NOS speedos can have problems due to congealing lube internally... I would want verification it worked properly...
well, i thought USA had wandering tumbleweeds- but now Horses too????? ... From: tomswifty99 To: Honda_SS125A@yahoogroups.com Sent: Wednesday, February 04,...
Hi, I dont nkow how much my cheaper/expensive but CMSNL hve these in stock- i believe. Ive often toyed with the idea of a new one on my bike, but hey i can...
... mufflers, for my C95 (CA95)that have "passed through" the system unscathed! I think the point here is if you need the items and there is only one supplier...
Hi all, im currently working on my carb, i stripped it down, cleaned it up and now on the reassembly side and hit a small bump... There appears to be no...
I'm taking this out of an original honda shop manual. The float level gets set at 21MM or 0.827inches. Don't let the weight of the float compress the needle...
HI, 21mm seems too high so the float bowl - so ihave set it to the specs in my other honda manual 18.5 mm Ive set the air screw to half a turn out, the needle...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
