How do I submit my SS125 into the Database Age Guide? I would be interested in others who have not submitted thier numbers. Thanks, Kent Rhodes 1969 (...
Super, we look forward to seeing them. regards Robin Kent Rhodes <prop@...> wrote: Oops, sorry. I found the little tab. I've entered my data. I'll post...
Hi I have a question for the group.I just receiced my motor back from restoration and I put it in the frame today.The clutch pull seems very stiff.It has new...
Hi, you can strip that down. its a worm gear assembly, perhaps the old grease has dried out. I would strip it, use wd40 to clean it up, pack with grease and...
Two other places to lube - lever pivot (where bolt retains the clutch lever) and the cable - check the cable by disconnecting at both ends.. if it slides...
HELP!!! I was cleaning the ss125 and I accidently threw away the retainer that the 2 screws go through that hild the drive spocket on. Does anyone know where I...
I'm retoring an ss125 but as usual with old jap bikes getting exhaust systems is the biggest problem. Has anyone got a supplier or a good alternative system?...
Derek - welcome to the club!! and by that I mean the club of guys searching for a source of old parts for our babies!! yes, the exhaust is quite rare... they...
Hello. After March 7th, I will know if a party is going to purchase one from me. If not, I have one Brand New genuine Honda Right Side, and one nice used right...
... clutch lever) and the cable - check the cable by disconnecting at both ends.. if it slides freely, it should be okay ... contacts the clutch release...
Just a comment on someone's suggestion regarding the Dennis Kirk "best equivalent" pipes. I just aquired a "survivor" with what seems to be equipped with one...
you are correct that there are serious interference issues...unless you "tuck in" the aftermarket exhaust carefully go to my pics (restore to ride) and you...
I'm unsure of which piston ring is the top and which is the 2nd (middle). I posted 2 pics to help explain. The first picture is a ring that seem lighter than...
Actually, it was already on the bike when I purchased it. It wasn't the most "elegant" installation but it is functional except for the banging on the pipe. I...
Hey, I just found the bag the Kick Starter came in; Marketed or Manufactured by EMGO PN; 83-61610, "KICK STARTER HON CT-90 #28300-23 / 040-000, Made in Taiwan....
Can anyone reccomend a good oil to use? I would be putting it in a freshly rebuilt engine spring time temps here are around 45 degrees F.What would be the...
I would go with your favorite brand of 10-40, and change it after the first 25 miles, then at 100 miles, then every 400 miles after that. Desert Todd ... ...
Gentlemen First, the manual says use a 20W at 45F (you did mean 45F didn't you?), but I would feel comfortable recommending a nice 30 weight(multi-weight or...
rare OEM tool kit on ebay, a 'must have' for the perfect restoration - item # 370028300577 this is a code 237 tool kit, but it is a 'double snap' bag that is...
Hi, im in the middle fo changing internet provider, so its a bit like moving house lol....i thought you have the top ring with is a scraper ring, then spacer...
I think you're correct. I found the answer in the CD175 section of the Honda Manual. The ring with chrome is the top, middle ring is all black, bottom is the...
HI, Tight piston pins?... you mean the one that holds the piston to the small end of the crank. If so.. if its tight on the small end, you need to examine why....
Thanks to the group for the oil suggestions!! Yesterday I finally finished the install on my rebuilt motor and started her up.The engine sounded great and I...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
