Ed, When I apply a load to the generator, the voltage doesn't start to drop off until after reaching about 17 amps. Applying further load causes the voltage to...
One day when I measured my eu2000i's output, I found that the maximum power output was about 1850 watts. After that, as I added resistive load the voltage...
tigerwillow1, Looks like you may have the same problem as I. Looking at the wiring diagram, it appears that the overload control must be contained in the...
I bought a new Honda eu20i (same as eu2000i, but with 230 volts, for different market)a few days ago, to use at our upcoming HF field day next weekend. I set...
Is the Rf via ac cable to your DC power supplies ? or via EMI RF emitted from generator? Would a metal RF shield enclosure work ? (ventillated of course) Could...
I'm assuming your are operating your radios using AC. If you are, the first thing I would do is to use an automobile battery charger plugged into the Honda...
I think it is via the ac cable, JWB. I am not sure what would work - was hoping someone here that had similar problems could point me in the right direction. I...
Yes, the way I had it setup, was running AC from the eu2000i to an Icom power supply, and then to one of the HF transceivers. I avoided using one of my...
Depending on the battery charger you use, it may produce some hash itself. Ideally you would have a battery of sufficient amp to be able to handle your useage...
In my experience a marine deep cycle battery will last the whole 24 hours of field day for me running 100 watts. I always keep a back up battery around and...
Sure.batteries would work and would not create interference, but.that is not the reason I paid $ 1300.00 for a new eu2000i. That is like buying a flashy new...
~~~~~~~ I found this usefull info on rfi suppression on eham.net. I will try it out as soon as I can, 73 ZS5J ~~~~~~~~ In an earlier review of the Honda 2KW...
... ...the cable is case hardened and is impervious to bolt cutters. One would need a cutting torch, or a disk grinder/cutter to get through it. Chris, that...
Robert, I'm sorry to say the company that made this lock has long since gone out of business. I purchased this one while living in England and used it to...
Sorry that this is somewhat off topic - I have an EM7000 (inverter) generator and it may be close enough to the EU series that I thought that I would ask in...
In addition to using my eu2000i with an RV, I'm going to have an electrician hook it up for emergency power supply in my home. I'll have a standard switch box...
I will be buying a generator/inverter very soon. I will be getting it for emergency backup mostly for my house, ocassionally use it for other things. My MAIN...
The Dunkirk web site does not provide sufficient information. Although it indicates a single 15 amp circuit is all that is required, it is not clear if that...
In a message dated 11/28/2007 6:46:18 AM Pacific Standard Time, ... What is the voltage and amps needed for the water heater (you should be able to look that...
... I am guessing that your boiler has a small circulation pump and some electrical controls. I have a 1/5 hp pump and 24V DC controls on my boiler that pull...
... cord shouldn't be more ... Uhm, not that one :-) ... If you want to do 50ft without much loss, or financial pain, I'd get some 10/4 and call it done. If...
I have made a relatively secure framework or platform that holds two generators in the bed of our pickup. Some of you might be interested in learning about it...
Is there any difference in output from the 15A receptacle , and the banana plugs ? Seems I read somewhere that you could get more power from the banana plugs,...
Gary, thanks for the response. Here's a stupid question: In 10/4 I assume 10 refers to gauge. What does 4 refer to? Thanks, Steve ... cord shouldn't be more ...
The number of individual wires in the cable/cord..... In a message dated 12/3/2007 6:29:00 P.M. Central Standard Time, steverothman@... writes: What...
I had not started my eu2000 for 3 months.... when I tried, it would not start.. I put it on the bench and took the side cover off, opened the carb drain and...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
