I'm attempting to install a 292 in a 1960 Biscayne, and it's not for the faint of heart. The biggest advantage that a 292 has is torque. Inline sixes are ...
I believe it is the original aircleaner and I need to look at the numbers on the rear right side of the block I guess.I will look tomorow..Thanks for all the...
Thanks a lot for your reply Iam going to replace my 250 cid with the 292 in my boat so I wont be using the side mounts it is a mercruiser buildup so it...
I'm hoping I'm not the only one who spreads a project over several years buying parts and hiding them away and accidentialy buying the same part again and...
Hello again ! I would like to hear from all you experts on what to do to a 292 core Iam rebuilding for a boat , Iam looking to acheive the most tourqe for the...
I would drop the MSD in favor of a stock non computer GM HEI unit. If you put in the same crank in you took out I wouldnt waste time line boring it. a good...
Here's a few tricks I learned as far as a high-torque 292 goes: - you can still purchase flat-top pistons (they were installed in propane-fuelled 292's) that...
I am pretty sure that you can use 283 or 307 pistons in the 292. they both come with flat tops. ... From: Jeff Christen To: GM_Inline_6@yahoogroups.com Sent:...
OK , look in mikes garage, and see a car (46 Chevy) sedan that was purchased 10 years ago, 250 six done, 4 years ago, transmission 6 years ago, floor in car...
For a Mercruiser build you would probably better off going for a Mercruiser marine camshaft for the 250 which is profiled to give lots of torque at low RPM's...
Look in the engine displacement post. Also line bore only if needed, you are not going for high RPM's so the balancing is going to be a waste of money unless...
hell i'm not that old, and i've done it several times. that's why i started the practice of making a list of what i need and what i have. like a have list...
just put a deposit on a 1947 olsmobile 238 flat head six with a hydra-matic trans and drive line/rear end I have a 37 1/2 ton chevrolet truck and will be using...
well geee wiz jim what is the ultimate inline? ... From: James Mansell <jamesmansell@...> Subject: [GM_Inline_6] To: GM_Inline_6@yahoogroups.com Date:...
Oh well. Hate to see you go. You can actually do this yourself. Go to the top bar where it says the groups name, right above there is says "Edit Membership"....
I am thinking of putting a 47 oldsmobile238 six cylinder into a 37 chevrolet 1/2ton pickup the truck will have a 37 gmc front end. gmc ran a 230 oldsmobile...
Tough to lose a little possey rider. Hate to see em go but git a long little dogey. ... From: strummin67 To: GM_Inline_6@yahoogroups.com Sent: Friday, March...
If the engine your putting in is roughly the same size as the one that was in it then it will fit. Without actually seeing it there's not many particulars we...
First measure the fire wall to the radiator and see if there is enough room, the Chevy's and GMC's usually had lots of room.If not can you move the radiator...
Hello Again ! so i have done it, sent my newly aquired 292 ,off to the machine shop for overhaul/ sprucing up , Iam looking for advice on for it , I want to...
Hello All, I'm not really familiar with this Olds engine or the 1937 trucks so I'm not sure if I can help you. I have a pair of 1936 Chevy sedan project...
Anyone have a spare Mallory distribor cap (red) for an HEI that they will sell or trade??? Mallory stopped making them. I bought or made all the accessories...
