Since the truck has not had the diff fluid changed in a while you can figure out your ratio and service the diff at the same time. Remove the cover and count...
That's Ford 5 on 5.5" to 8 lug! ;^) I was going to do the reverse to that with my J4000, but then thought "why the heck cut down my weight capacity with 5...
That's Ford 5 on 5.5" to 8 lug! ;^) I was going to do the reverse to that with my J4000, but then thought "why the heck cut down my weight capacity with 5...
oh, wait a minute... haven't done this in years. my numbers were wrong. only raising one tire does double the driveshaft-to-tire relationship, but disregard...
3.54 was also common for 4 speed rigs prior to '80. Mine had 3.73 (which I really liked with the 17% O/D QT and 33" tires for freeway cruising) Jim Blair,...
I would take one of the rear belts and use it in the middle front, swap the other rear belt to the rear middle and put in "universal" belts. On the other hand,...
See if the front tag is still in place. Tomorrow I need to check the J20 axles in the parts truck I have to see what ratio they are. Still trying to decide...
As was explained by others it will stay in Edrive or out of it depending on the last position the vacuum put the shift lever. You can also mess with the vacuum...
heh. marks on the driveshaft and tires are a must (and kinda implied ; ) there is a little trick that you have to use sometimes, too. often, one tire drags...
Now, unless you have one of those minds that can write poetry with one hand and do math with the other while singing opera, (or you're as sharp as Neal!), you...
Thanks, I answered most of my own question yesterday when I thought about it and looked at the input on the vacuum actuator, one for each side of the actuator....
In my ever ambitious mind, I have the idea of converting the Ford 8.8 I have sitting around to a full float for installation in my Cherokee. Two reasons first...
Don Weber
tuba_umphblat@...
Nov 11, 2009 2:52 pm
96950
Now that's pretty smart thinking of you, Neal! Sincerely, Greg Taylor <>< Rochester Hills, MI 1989 Jeep Grand Wagoneer "TRMN8R2" 330-CID AMC...
think you  Erik D.Hobbs  ________________________________ From: Greg Taylor <amundaza@...> To: FSJ-List@yahoogroups.com Sent: Tue, November 10, 2009...
i have a Spicer book if you want to shoot me your BOM #. another way to check is to jack the back of the truck up and put it on jack stands. put the 'case in...
Hola~ I have the chrome seatbelts with the stamped logo. I have four installed in my car. I'd like to add seat belts to the middle front and middle back seats....
Michael O'Brien
mkobrien@...
Nov 11, 2009 4:40 am
96945
Dana 60 rear axle only. Front is a Dana 44 HD. Sincerely, Greg Taylor <>< Rochester Hills, MI 1989 Jeep Grand Wagoneer "TRMN8R2" 330-CID AMC...
It is most likely a 3.73:1 rear axle. 4.10 was an option. You could always pull the cover and count the number of teeth on the ring gear and pinion. ...
Como esta Miguel. If you have or HAD the chrome seat belts with the stamped Jeep logo, you would have to find them and have them rebelted. There are some...
I have an 86 J-20 with a Dana 60 rear. How can I determine what ratio it has. The ratio tag is not in place on the left side of the axel. I do have the bill of...
Lance @ Sandy
oryx2hunt@...
Nov 10, 2009 9:58 pm
96940
I'm new to the way my Cherokee works, so I have a question. I bought this truck, semi-disabled and have been working on it casually for a year, so I have not...
Hola~ I'd like to install middle seats in the front and back of my 67 Wagoneer. I'm looking for belts that match (they are like airplane belts). I've found...
Michael O'Brien
mkobrien@...
Nov 10, 2009 2:04 am
96938
Dave, The hose runs under the vehicle, all the way back with the wireharness along the frame, so I would think bottoms-up. Sincerely, Greg Taylor ...
I knocked the nozzle off of the rear window washer at the car wash. I am trying to fish the feed tube out of the hole on the right side where the nozzle fits...
I can get the part numbers off of most of them. I will try to get a list but probably won't happen until next weekend... got that lights turned on in the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
