I'll have to search on the board to find him. I would love to get a swap like that in my Waggy, although I probably couldn't afford to pay a shop to do it....
Undo the 6 little bolts holding it to the knuckle, then take a 2x4 and whack the spindle. It should pop off after a couple hits. (works for me!) Re: parting...
Someone mentioned that in their newer car with an electric fan, turning on the AC activates the fan. That would give you almost instant cooling I would think....
With no mechanical fan and an electric fan not wired into the compressor there is no air circulation through the condenser when stopped. Not good. I thought...
Well DUH, of all the things I have lost the one I miss the most is my mind. I was associating the small bolts to the caliper mount instead of the spindle thus...
Some time ago there was a discussion on electric fans and someone had an electronic control box that controlled the fan and as I recall it upped their mileage...
That's hard for me to believe. It must have been on a very small car with a very big alternator to load the engine down that much when charging. Russ in NH ......
I'm going to control the fan from the compressor lead to begin with. If it works, I may add a switch inside so I can control it manually. Turning it off when...
Fairly sure it was an SJ. Maybe they will respond. ... From: Russ To: FSJ-List@yahoogroups.com Sent: Friday, August 01, 2008 10:39 AM Subject: Re: [FSJ-List]...
Mine goes through a relay from the temp sensor or a different relay from AC compressor. Since my nifty jifty junkyard relay base has a couple diodes in it I...
I thought about the diode route but I think I'll just put the manual switch in the ground side of the relay coil. If I forget to close the switch, I bet I'll...
The stabilizer pads and rods that hold the rear leaf springs together have melted. So my leaf's are shifting in the packs on one side. I was looking for a...
I was trying to keep the fan from running all the time the AC was on because the Cummings runs quite cool. I forgot about no air movement when stopped. I...
This is the Full Size Jeep Mailing List (FSJ-List), of the International Full Size Jeep Association (http://www.ifsja.org). Its purpose and direction is for...
FSJ-List@yahoogroups....
Aug 1, 2008 7:47 pm
92991
I had two 10" electric fans mounted in front of the condenser on my 88' GW that turned on when I turned on the AC and if the engine got above a certain...
Don Weber
tuba_umphblat@...
Aug 1, 2008 9:28 pm
92992
Dean, while i have seen them break it was usually through stupidity or someone trying to jump the truck or someone running huge tires and a hydroboosted...
OK here is an ad from craigslist and it might be a 4 dr Cherokee and not a Wag. I can't tell! http://chicago.craigslist.org/sox/car/779649631.html 360 TH400 ...
lost the original post (Hotmail blinked as I was typing) but the knuckles should bs saved if A: They are flat top (especially the rh one!) and B: you are rough...
A. is not true and B. is not likely. I rather fell like I should save the axels, not sure why, what do you think? If I do save them do the knuckles have to...
Hi, my '90 GW has a serious leak from the steering gear box and an excessive amount of play in the steering wheel. I've seen kits to replace old worn out...
I have never taken an axle apart but I would think that the axle shaft must be able to fit through the hole behind the spindle. I have seen many pictures with...
My 88 had a serious leak that turned out to be the low pressure hose clamp on the pump. It rusted away. The same 88 developed a lot of play in the steering...
Dean, you are correct. once the spindle is off then it is just a matter of a little work to grab the axle and slide it out through the hole in the knuckle. you...
There's an adjustment for the play on the top of the steering box almost under the lower radiator hose. Loosen lock nut with an open end & drop an allen wrench...
What do y'all make of the green jumper wire on my door switch wiring? http://industryfigure.com/berkeley/fsj/images/door_switch1.jpg IIRC, my dad had the...
I would suggest having the Allen wrench in the screw before loosening the nut so screw does not turn and go further out of adjustment and take it down 1/4 turn...
What parts are necessary to install a camshaft, or are just a good idea to replace? I'm planning on buying a Lunati Cam/lifter kit in the near future and...
i have a 66 gladiator and after removing the tire, i cannot get the cover off to get to the brakes. i've wailed on the back rim, used pb blaster, vinegar and...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
