A: Wish it was closer to me! I've busted several pedal bikes trying to get back into shape (Hey! Round is a shape!) I use the local Freecycler a LOT! Last...
I was in there yesterday and took the picture of it. Had one on the shelf for about $13 and I picked it up. Thanks again! Sincerely, Greg Taylor "Neal...
You have to be absolutely certain you lock in the hubs before engaging 4wd or you will fry the viscous coupler in your transfer case in short order. Patrick V....
Hi Patrick, I no longer have a NP229 (VC) t-case installed. Mine went south a few years back. Local AMCer had a rebuilt NP228 that I got from him and that's...
Came across this link, as my old H20 injection unit split a seam (it's 30 years old). I might build one of these up and see how it works on the 360 in the '89...
I did this in the 70s on my Trans Am which I raced every weekend. The water injection seemed to make the engine run smoother and helped keep it running ...
Is there any body shop in the midwest that specializes in restoring J- series vehicles. I need an 82 Cherokee restored, but I want it done right. Todd 1982...
Hi Guys, Thanks for your input. In looking the system over, I see that my vacuum lines are not as per Collins page. Need to get it figured out before any other...
I guess you would have to define 'Midwest'. Where are you located? Zack Heisey Z&M Jeeps Ltd. zack@... www.zmjeeps.com 419.893.4JEEP (4533) ... From:...
Don't feel bad Dorien, out of the 8 FSJ's (82-88)I've had NONE has matched any of the diagrams! Just find the "closest" diagram that matches you have now &...
... Warn ... Thanks. ... Greg, I have a 1973 with a 360,th400 and Qtrac. I installed Milemarker hubs on it and I cannot tell any difference in mileage at all....
Looks like he is near Madison Wisconsin according to the www.tds.net<http://www.tds.net/> website. Mac CA_FSJA moderator California Full-Size-Jeep Association ...
I have already purchased some of the parts and will put it together next week. Picked up a hypodermic needle at Meijer pharmacy for 25- cents. Nabbed the...
Well if your 4-wheel drive is always on with the Q-track your front driveshaft is still turning causing drag on the driveline, in general anything that reduces...
Don, Do you have a part-time kit on your QT or do you run it in e-drive? If you don't have the p-t or run in normal mode with the hubs unlocked, it will burn...
On my old 88 Waggy, mine when up and couldn't get them at the time. I removed them from the air injection rail, and installed a galvanized pipe cap over the...
For some strange reason, today, my gas gauge started 'working' Well, the needle started moving. I ran to the gas station with my 3rd mortgage to fill up, and...
They switched the MO in '86. Sounds like someone switched in a sender on the opposite side of the switchover so it reads backwards and a connection got...
Anyone done or have ideas on converting the tail gat in the GW to a side hinge instead of hinge at the bottom. They are very heavy to open and close and in...
Are you sure that gas nozzle was not sucking out the gas? 8^) Yeah probably the wrong sending unit! I am wondering WHY the sending unit started to work now....
... Being a little late to this thread, the way I have done it in the past is to wire a 12v relay into the power feed to the coil. When power is applied (key...
Group, I have cleaned the distributor and replaced the wires but Uncle Buck STILL cuts off and will not start after running for abut 30-45 minutes. Any more ...
Mark Jackson
markjackson@...
Aug 3, 2007 4:40 am
87030
Well it would be asy enough to use 4 hinges since suburbans do have 2 doors in the back. I'm at a loss on the holding it open part, unless you have a hinged...
Your fuel pump may be to tired to feed a 4bbl carb for long periods of time. There could be a factory defect in the carburetor like a bad or missing part. Mark...
I think it's option FUBAR. either messed up wiring or the fuel sending unit is malfunctioning in such a way that it would read backwards, most likely both....
A: The main thing you will need is a 4bbl intake if you want one! I still have your 327 with the TH400 adapter and you can have the TH400/QT from my J4000...
