Doesn't matter where you mount the PCV as long as it is clear underneath. As for the brakes, it may be the valve in the brake line below the master is jammed...
Hello again Jeepers I'm in a bind. My driver's door window motor has finally quit. Seems there were several different motors used in the last year. I need the...
Sorry to chime in so late, but you have adjusted the rear brakes, haven't you? If you haven't already done it, it would be worth doing a rear brake tune up...
hey there jim-just wondering if you've found that email address for that guy who shipped over the m715's here from the phillipinnes-I am near oakland if there ...
Does anyone have any opinions/experience with napa brand oils, including their synthetic, also, does anyone know how valvoline vr1 compares to mobile 1? thx...
Gerber
fullsizejeep@...
May 1, 2006 10:28 pm
81848
I was just thinking about that, actually. The master cylinder will still be replaced, even if it isn't "necessary". I'm going to do a full rebuild of the ...
For "store brand" oils, I look to see that it's rated to meet or exceed the standards out there. I would think that most current oil out there is probably a ...
If you're going to completely go over your brake system and don't mind putting some money into it, you may want to consider a disk brake conversion for the...
I have heard that before, the whole specification thing, question: to they test the longevity of the oil against breaking down in the API testing? ... ...
None
fullsizejeep@...
May 2, 2006 1:54 pm
81852
Hi all, I would like to repaint my 1966 Gladiator in a stock color. It's currently faded grey over an original white. What are some links that may be useful...
In a message dated 5/2/2006 7:02:55 AM US Mountain Standard Time, scramboleer@... writes: I would like to repaint my 1966 Gladiator in a stock color....
If you didn't have them, you'd notice. Drum brakes are under rated. My '68 Pontiac will stop in a heartbeat and it had drums all the way around. So did my...
The motors are listed at partsamerica.com amongst other places like autozone & advance auto parts. You might want to check there. Close to $100.00 & they show...
I'm sure someone here knows more about this, but IIRC, that's pretty much what they wind up testing, is the breakdown of the oils over time. The main...
I'd like to go 4 wheel discs at some point, if for no other reason that big vented discs would be more reliable and easier to work on. BUT, I'll wait until I...
i tend to agree. they definitely have the stopping power, it's the auto-adjust features and the booster / proportioning systems that drive them that are much...
Thanks Tom I'd already checked partsamerica but I'll look again. I guess Autozone and PepBoys will be my next stops befroe I start checking junk yards. ... ...
Disc brakes might be superior, but drum style brakes have been in use for over 100 years on wheels and transmissions for cars, trucks & motorcycles and still...
I just put a D44 from a Isuzu Rodeo, in a YJ. It has 4.30 gears and a Spicier limited slip and disk brakes with the internal e-brakes. you may have to move the...
See if you can get me numbers off the old one. It may cross to another Mopar product of the same vintage! "If we ever forget that we're one nation under God,...
Haven't found his email yet, but I found these: http://army-guide.com/eng/product.php?prodID=2343 http://car-action.com/offline/01/011019_airshow/km450.jpg ...
Thanks Jim Here's what's on the original: There's a label on one side of the motor itself that has a logo on it for Rockwell International and part # 55154563...
Seems there was several different lift motors used in that year. Mine uses a spiral "cable" instead of flex-trac to raise and lower the glass. ... From: "Russ"...
aaaaaaaaaaaaaahhh!!! that thing is SICK! it looks like my J10 with the way the fenders (which i dig waaay more) are instead of the flat piece of steel plus the...
speaking of window regulators, (sorry to hi-jack a thread), but has anyone retrofitted any GW regulators and door lock mechs into j-truck doors? how "bolt-in"...
Hey everyone I have been ripping out the floorboards one side at a time, the passenger side is almost ready for welding. I would like to know if POR15 is thin...
