e-mail me direct at recon2311@... and we can set up how to ship it my zip here is 84321 for shipping quote or you can call me at 435- 753-3978 night or...
Rig is 327 with TH400 trans (someone want to pass this on to the AMC-list?) http://www.snort4x4.com/forum/showthread.php?t=26772 build your truck right the...
I guess you forgot about the off-list part! <G> What did they charge you for the rad? I got a new 3 core online for @$130 to my doorstep. build your truck...
A: You only need 2 lines from the switch (and one going in with vacuum) to the transfercase shift motor. It shifts bewteen 2 and 4wd. Hi and Lo are the lever...
A: I put an '83 Cherokee V8 rad in my '73 J4000 no prob. You can't easily put a 8 cyl rad in place of a 6 cyl one, but it'll sort of work the other way around....
Recently I bought a Mopar V10 4 speed auto trans (found out that except the torque converter it's the same as the diesel one) and NV241 DHD tcase. I think it's...
I'm here still (and many other lists too) My '83 Cherokee is gone but I've had a few come and go since then. Current flock is '73 J4000 (junk hauler and daily...
Dakotas were built off the Jeep Comanche line. The early ones even share the same boxes and tail lights! (I've been looking into a Comanche with AMC V8 swap) ...
A: SO how did this turn out? From: "gondorian_ranger" <gondorian_ranger@...> Subject: Transmission removal (727) Help weekend project!!! I removed the...
In a message dated 11/2/2005 1:26:27 AM US Mountain Standard Time, carnuck1@... writes: Dakotas were built off the Jeep Comanche line. The early ones even...
My '87 Comanche came with 3.08 gears and my '83 Cherokee and '84 J10 (both with 4.2L) came with 2.72 gears! build your truck right the first time! From: "Neal...
A: You need a special adapter for TH400 to D300 (I have the adapter sleeve, but not the spud shaft unless your D300 is 32 spline) Late model '70s IH and YJ...
... I know, it is a matter of cutting the radiator mount metal to allow for the wider width of the V8 radiator, and that's about it aside from welding the...
In a message dated 11/2/2005 1:51:52 AM US Mountain Standard Time, carnuck1@... writes: A: You need a special adapter for TH400 to D300 (I have the adapter...
Hi ,I need to know if ,I need to fill the lifters with oil when I put them on ,looked in the book but could not find anything ,In it, Any info would help ,And...
It's not a bad idea to do so. I put the new lifters for my rebuilt 360 upright in a coffee can and covered with oil for a couple of days before installing. ...
I need to replace the leaking power steering gear box on my '89 Grand Wagoner. It appears to be a 4-bolt Saginaw gear box. Does anyone know if a 3-bolt box...
The last time I installed a set of lifters was several years ago, but the instructions that came with the lifters said to put them in a container of oil deep...
I put a 3 bolt GM box in my 79 wag. It worked fine, but I don't wheel over rocks and in mud........only snow. ;-) It was a straight swap, but I did have an...
Check with Xtreme radiators on the web. Got a new 4 row for $199 and put it in my J-10. Jim Blair <carnuck1@...> wrote:A: I put an '83 Cherokee V8 rad in...
For a quick ratio many are using an S10 box. Apparently it is also 3 bolt but bolts directly in. Use the later 1990's or early 2000's models. Have seen many...
I put Summit Racing generic alum race radiator in mine. It's a 2 core but core are 1" wide. Used the Ford version to get inlet/outlets in the correct place....
Gabe, I'm near Hickory, NC, so a visit would be rare, but I enjoy wheeling with you guys when you come to East Coast Invasion at Uwharrie. Hope to be back...
Rod and Joan
rjoanie@...
Nov 3, 2005 5:49 pm
79443
I have a FREE rotor (new in box) to anyone that wants it ... just pay postage costs. I bought it years ago for a 1974 Cherokee S (360). It's for the...
A: I could be wrong. I know Jeep used 999 automatics with the D300 and round adapter ring. If your D300 has the round (and not Texas shaped) input, then it...
I'm getting ready to install the 195-degree thermostat in my Jeep, in place of the 160-degree unit that I had installed. I am planning to use silicone for the...
when provided, i always like to use the paper gaskets for thermal expansion reasons. it does provide for a little give without breaking the seal. i also like...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
