There's a miseable ring in a groove on the inner face of the hub. You have to make a little 90 degree tool out of an awl or ice pick. ... From: "Eric Lusk"...
Ahhhh...Ya got me Obi... frank n texas ... From: "Obi-Wan" <bvh@...> To: <FSJ-List@yahoogroups.com> Sent: Friday, October 01, 2004 12:14 AM Subject:...
Find and buy a set of those s/s dental picks like the dentist had....I think Harbor Freight has them..Set of 4.. frank n texas ... From: "Don Hansen"...
I spent part of last night looking for that ring, and strangely enough didn't see it. Will have to take a look again in daylight, and maybe when I'm more sober...
Had a bit of a problem arise when putting the low range back on my QT. Discovered that the 10-spline Main Reduction Shaft was twisted! If anyone out there has...
Eric...That happens to me all the time...Trick is to just close one eye and then look for it.. Hope ya find it.. frank n texas ... From: "Eric Lusk"...
Its not round like an o-ring, but square in cross section. Its just inside the outer edge of the hub. You have to look REALLY closely to see the little gap...
A: Actually, he was going to get hoses custom made when they are already available. Why pay extra to reinvent the wheel? <G> The rear hose was already longer...
Sounds like the Dentist dental pics I mentioned earlier would be a "good thingie" here...Especailly the one with the 70 + degree angle on the tip.. frank n...
"Is there not a way to... determine if ya have it or not...?" I think OBD2 requires a plug inside the vehicle, kinda like this purple one, and the others: ...
This from SoCalXJ: To: socalxj@yahoogroups.com; socalxj@yahoogroups.com Subject: RE: [socalxj] Re: OBD2 in '96 or '97? it was split some 96 were full odbII and...
... On my '77 Wag, the ring has a round cross section. Not that that makes much difference if Eric can't even find it, but I imagine the round ones are easier...
Obi-Wan
bvh@...
Oct 1, 2004 6:41 pm
69639
Clean it well, light it well and then use magnifying glass? Hard to believe a ring in a groove would be that tight Must be some really close manufacturing...
76 JEEP WAGONEER 4 SALE IN TACOMA, WA. MAKE OFFER!!!!!!!!!!!!!!!!! HAS 401 ENG, GOOD TRANNY, SOME T-CASE PROBS. RUNS GREAT, IT IS MY DAILY DRIVER. THE ONLY...
Testing new email settings that my ISP was nice enough NOT to tell me about. Lindel ... Outgoing mail is certified Virus Free. Checked by AVG anti-virus system...
OK, my buddy asked me to check into this & has no computer. 94 Wrangler with the 2.5 engine. He says the Brain box/computer is fried, visible arc/burn marks &...
http://www.snort4x4.com/forum/showthread.php?s=&postid=116159<http://www.snort4x4.com/forum/showthread.php?s=&postid=116159> [Non-text portions of this message...
He needs to post ALL of the numbers and letters on his computer/ECM! Possible causes: Bad grounding wires/cables could cause it. An electrical surge from the...
Yeah, thanks everyone. I haven't managed to get back to working on the Wag today, just got done with a long day at work. But after reading responses, you...
OK, tell your friend if he doesn't know how to properly diagnose the short that caused the ECU to fry, pay someone to check the voltages at the harness pins....
j2sax@...
Oct 2, 2004 3:00 pm
69652
Sounds like good advice to me pal.. Sometimes we can help and sometimes we cannot or should not.. In this case, I think you helping a bunch.. frank n texas ......
