Had same problem, left me stranded a few times. Pump was good. Turned out after replacing everything one thing at a time and sent the fuel pump assembly. to...
36355
kbretz
2:06 am
Should have checked the fan before installing to make sure it worked. Will proceed with the ground check and double check the splices. Could the switch have...
36354
Jumper
superxparts
1:41 am
Ken... Make sure the ground is grounding.. Make sure your splices are wire on wire vs wire on plastic covering... Check your switch and the wires to and fro.....
36353
rejoicex
1:33 am
Grizz, I would like to know more about the carb. mod. If we could eliminate electrical draw maybe the stator could hold up. Suprx443...
36352
kbretz
1:24 am
Wired up the new fan and it doesn't run. I recall the old one was not running when I shut the bike down. Figured it had blown the fuse when it gave up the...
36351
Jumper
superxparts
May 22, 2013 6:02 pm
Yes. Attached to fuel pump..I'm guessing that you could hook up a fuel gauge, turn the X on, should build up to 48-53 LBS pressure (or somewhere close to...
36350
x4271999
May 22, 2013 5:35 pm
Will Check. Got a lot of good ideas thanks to all. Switches are not that expensive got rear but have to order front from Honda. I have a Buell switch on now...
36349
Robert Gerhart
gerhart_97
May 22, 2013 5:26 pm
The Deutsch connector right under the seat is an easy place to poke around with a continuity tester to see if you are at least getting signals that far....
36348
dlwatk91
May 22, 2013 5:05 pm
Thanks for the reply! Would that be located in the tank with the fuel pump? Donnie...
36347
Jumper
superxparts
May 22, 2013 4:51 pm
Oh yeah.... Welcome to the X Family... Ask all the questions you want... We've been there.. Jumper...
36346
Jumper
superxparts
May 22, 2013 4:46 pm
Fuel pump regulator... Jumper...
36345
dlwatk91
May 22, 2013 4:06 pm
Hello all, Ok so i have spent hours going through these posts searching for my issue or similar and trying others solutions with no luck. My problem: the bike...
36344
Thomas B. Jr. Gough
goughthomasbjr
May 22, 2013 6:37 am
es there is a fuse for the ignition and a solinoid or relay if you prefer. Under the seat on the left side of the bike are the fuses and the relays are under...
36343
Thomas B. Jr. Gough
goughthomasbjr
May 22, 2013 6:22 am
Last time the brake lights quit on 441 I found that the front brake light switch had gone bad, the rear hydraulic switch was sticking a bit, a wire had pulled...
36342
Jumper
superxparts
May 22, 2013 12:57 am
HMMM... I'd try a new bulb just in case...Check fuses.. Then... Get out the wiring schematic and start chasing wires... Good luck.. Jumper...
36341
x4271999
May 21, 2013 8:40 pm
still no light jumped both front and rear switches. I remember the rear switch stuck a few weeks ago but worked ok until Saturday...
36340
x4271999
May 21, 2013 7:18 pm
Checked front and rear...
36339
Jumper
superxparts
May 21, 2013 7:12 pm
Please join us for Rally 2013! Pre-Rally Welcome Party by Northstar Powersports, Albert Lea Minnesota, July 10 Rally 2013, Valu Stay Inn (formerly Downtown...
36338
Jumper
superxparts
May 21, 2013 7:08 pm
Get a small gauge jumper wire, jump the front and then rear switches. Make sure the key is on. If bulb lights up, clean the front switch and make sure the...
36337
Quentin Jensen
qjensen99x
May 21, 2013 6:29 pm
Is there a fuse for the ignition I'm dead at the wires? Sent from my iPhone ... [Non-text portions of this message have been removed]...
36336
Thomas B. Jr. Gough
goughthomasbjr
May 21, 2013 6:27 pm
Check your wiring and the brake light switches on the front and rear brakes. There is also a fuse that supplies power to the brake lights. GRIZZ ...
36335
Mark Lange
thumper5165
May 21, 2013 6:25 pm
Does the light not work from either the Front brake lever or the rear or are you only checking it from the rear brake pedal? Sent from my iPhone ... [Non-text...
36334
x4271999
May 21, 2013 6:20 pm
Changed bulb seems to have no power...
36333
kbretz
May 20, 2013 6:29 pm
I made sure I ordered the puller but will re-check it when it gets here. Thanks for the info! Ken...
36331
ROGER HODGE
rogerhodge4@...
May 20, 2013 4:26 pm
One note to follow up on Jumpers wire reversal remark---the va31 fan comes in two models that end with a simple letter designator that otherwise appears to be...
36330
fortworthx
May 20, 2013 1:38 pm
I'm trying to get the last few stars to align that will allow me to get there. Certainly could use some time hanging out with some of the X family....
36329
Jumper
superxparts
May 20, 2013 1:32 pm
YES! Dave, I messed up the post... I have had to wire the fan backwards to get the air to PULL through the cooler... Thanks! You coming to Elkton this week? ...
36328
Mike
way2coolwheels
May 20, 2013 12:59 pm
Sorry guys, I would love to join you. Unfortunately, I had to pay a tax bill that killed my plans. (A good reason for me to continue to promote the Fair Tax...
36327
kbretz
May 20, 2013 12:06 pm
Thanks for the advice. I sourced a VA31 fan and should have it in hand shortly. The fan on the old unit did pull off the shaft and after removal, it appears...
36326
Keith Nielsen
keitheliot_9...
May 20, 2013 6:41 am
I used a larger B&M cooler (10" by 11" BMM-72066 from Summitracing.com) and a ultra thin 7" fluidyne puller fan (from sportcompactonnly.com) and made my ...
