Repaired broken wire; replaced burnt spade lug, reinstalled regulator and used di-electric grease on both connectors for the regulator, started bike, low...
Hi, I have been monitoring my voltage at the battery for quite some time as well as the wires coming from the stator to the voltage regulator. The battery...
Has anyone here had any experience with a noisy belt making a whirring noise? My X makes just such a noise beginning at 50mph and gets worse at 70mph. It seems...
Might be to loose so the grooves on the top of the belt rub the lower swing arm. You might not hear it until you get up to speed. Check that out before you...
Great ... From: Joe <sullivan.j.t@...> Subject: Re: [EHRB] Voltage regulator To: Excelsior-Henderson-Resource-Board@yahoogroups.com Date: Wednesday,...
Is your plastic lower belt guard rubbing? Most guys toss them for that reason. B ... From: reggmansx <no_reply@yahoogroups.com> Subject: [EHRB] Re: Input...
My friend had a short to ground on his and it was located on the left side of the bike below the rear motor mount. The wires running under the engine had...
This mount (1376, I believe) has had a most difficult life and arguably, it has had an abusive owner. While there may have been a lot of love there, we all...
Hey Stiffy.... I think the number is 1375, and you are absolutely correct in every call you made about the deceased.....LOL!! Jumper will heal and in time...
That's a damn shame, but it's good to hear that Jumper is on the mend. Jumper - don't you have 5 super-x's in pieces somewhere? (or was it one in 5 pieces?) ...
Okay Laura, I think you're onto something here. May I throw in my .02 worth... How about burying 1375 in Jamie's yard ass first with its front end aimed at...
Is the belt aligned? Has the trans been rebuilt? Assuming this is done correctly the output shaft bearing could be suspect... When you change the belt, inspect...
LOL.....very good suggestions. Whatever happens, I think that #1375 should be immortalized in one way or another. It deserves it after the life it has...
Charley, My transmission was rebuilt years ago and the belt is aligned properly best I can determine. This was done by my local mechanic after new tires...
Come on guys, Stiffy your .02 is always worthy and welcome, but let's not throw Dirt on that baby yet while Jumper is recuperating. I was thinking that perhaps...
You might want to check the torque on belt pulley. I have taken several of these off that were barely finger tight. This is a known issue and the torque is...
Mr. Heaton pretty much promised the X world anything they wanted to hear. "Yeah we can start it back up".... "Someone is going to buy it all and start this...
Hey all, I haven't posted very much here, one of the reasons is my bike has been in the shop for over a year...yes a year. I bought my bike two years ago with...
It may or may not be a belt issue. That's mostly a rear mount thing. Anyway, if you are concerned about your belt, loosen it until you can twist it 90 degrees...
Ummm... I'm out of service for a few weeks and am unable to make it. I do thank you for the offer to share X times and laughs. Carry on! Take pictures!! Send a...
Ummm... I'm out of service for a few weeks and am unable to make it. I do thank you for the offer to share X times and laughs. Carry on! Take pictures!! Send a...
How does it break? Does the rubber pull off the metal washer? Do you have the chrome cap on it? The cap is part of the functional mount, nut just a pretty...
Glad to see you back on here Jumper. Heard about your mishap. Get yourself back inshape as soon as posible, the "X' world would not be the same without ...
The bracket itself broke in half. I bought what was supposed to be the better mount since the stock one broke. I just had the motor redone and the flywheel...
... the ... redone ... broke). ... why ... Yeah! I broke 3 so far and have been riding around for 2 years on the last new one I had purchased from the now gone...