... after ... earlier ... safety ... colorful ... If you take your bike to an X-specific shop like Jamie and Marty's (for example) and tell them to "do the...
I know a few of you who have 30k plus miles on an X. Chuck B., Russ & Jumper come to mind as I know they do ride theirs long and often. Would be interesting...
I had 58K on my X, the only problem I had was a burnt stator and replacing the charging regulator. I used Redline 20W50 oil, changing it twice a year, filter...
i have 51k on 799 - running very strong now, but has had some motor repairing along the way. caught on fire once, also rode through snow. still nothing else...
Geez Tony... I can't really say I have 59K on 1375.. Yes, on the frame, but in reality... 1375's motor has been an East Coast ginny pig... In and out quite a...
My Deadwood has had its share of "issues" screw that er "problems" along the way. Wiring harness burned up early on a few stators, a couple handlebar switches,...
Russ, Good luck on the surgery. I had that done last December. The recovery sucks but it was all worth it! I can twist the throttle on my Deadwood with out...
Anybody have step by step instructions on removing the rear cylinder head.I only have 30 lbs of compression in the rear cyl. I need to find out why. Thanks...
Heading to Waz's for our local chapter meeting. Looking forward to seeing everyone and will post pictures. Any Xer's in AZ. I have had it with the snow and...
Hey Rich If you want to know why before you remove the head? Squirt some motor oil in the cylinder and do a compression test, if the compression improves, the...
Can anybody recommend any t-shirt sellers that's got "X"/EH specific goods? I'm not an e-bay person, I'd just as soon have a phone conversation with the...
Marty and Jamie may have some www.superxparts.com or Terry here in Phoenix may have some stuff www.ehparts.net........ Chuck www.superxservice.com alabamax1521...
i already did the shoot oil down the hole compression check.It made no difference.I assume Jumper's on the right track. My real concerns are about ,how do I...
I have a lot of them. Many new some lightly worn. Dave former 2018 owner. ... From: alabamax1521 To: Excelsior-Henderson-Resource-Board@yahoogroups.com Sent:...
Hey Rich You will need to remove the front and rear motor mounts to drop the engine in the frame. You will need to grind a 5/16" allen wrench to get into the...
Apparently this is a Chapter Meeting but everyone is planning on it. I'm afraid that I can't make it this time, not quite 100% and a lot of driving ahead of...
I sometimes wonder what happened to all this stuff. I had a paper proposal for class - some righteous b.s. - but I couldn't get a nibble of info and had to go...
At the end of the riding season my transmission was acting weird. I'd put it in first and roll off at a good clip. Once in a while just after I got going the...
If your tranny is letting out a "clunk" like it isn't fully engaged it probably isn't. Are you using the factory designed " upgrade shift kit"? Did you lift...
Hey Russ, what does good ole 1103 have??? Thanks Howard ... Howard C. Roth Harleysville, PA http://www.dandyindustries.biz MSF RC #114900 IBA # 8524 01...
check your drive belt tension. If it is on the loose side you could be slipping on the rear pulley. Tighten it up or don' t take off so fast. Doug ... From:...
Howard, 1103 has the factory upgrade shift kit and the stock .040 oil jet. Its been a long time since I've seen that bike. How's she doing. Russ ... ...
It's doing well. I am making plans to head to Marty and Jamie to have do some things. They will do SuperXtune and get it to run right - it misses and stalls...
